Jump to content
SAU Community

Recommended Posts

It's on again boyz and girlz!!! Dyno day/Shootout at Boost Bitz JDM on the 5th of June, Bookings via email please to [email protected], Great day to be had by all. Whether you want a shot at the Highest HP run of your class or just keen to see what power your machine is making, this is the cheapest way to get on a dyno and chill with your mates!!!!

Details are as follows:

Equipment: Mainline AWD Dyno

Where: Boost Bitz JDM - 5/43 Leighton Place, Hornsby

When: Starts at 8.30am, Saturday 5th of June.

Cost: $60 per car with certified Dyno print out, lunch and trophies for highest HP.

Classes Are:

6 Cyl Highest HP

4 Cyl Highest HP

For additional info or phone bookings please call Chad on 0433 405 788. You can also PM me......

Link to comment
https://www.sau.com.au/forums/topic/319714-boost-bitz-jdm-all-nissan-dyno-day/
Share on other sites

  • Replies 54
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

AWD dynos also work with rear drive vehicles i assume?

How long is the day and what time would I have to turn up? Im not a morning person :thumbsup:

Can only SAU members go? I have some mates that wanna turn up and im also not an official member.

if we dont make a booking and turn up do we still get a run on the dyno ?

work is stuffin me around at the moment so dont wana book it then have to cancel cos of work :|

Hi Micheal,

Cruise over and im sure we can get you on if you make it. Thanks for the enquiry!




  • Similar Content

  • Latest Posts

    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
    • Not sure yet.  Was considering speedtek because it was rated to 800hp, but when I did some research about him I don't think I will go for that🤣 So maybe giken gear set, but I'm afraid it won't be strong enough🙄
×
×
  • Create New...