Jump to content
SAU Community

Recommended Posts

hey guys

latly iv been noticing my gtr is dropping oil pressure on hard accelration

mainly first an second gear drops to bout 2 bar and have seen my preset warning light come on at 1 bar

only for bout a micro sec, asson as i change gears pressures back up

normal driving not probs what so ever or even building boost slowly

motor has just under 6000kms on it and dosnt make any wierd knocks

motor feels strong with no lose of power (332kws)

usally iv got 2.8bar of oil pressure at idle

and bout 5-6bar a 3000rpm

im running an

apexi oil pressure guage

tomei oil pump

tomei sump baffle

head restrictor

motul chrono 300v oil over filling stock sump with an extra litre

is this the common rb26 problem that i keep reading bout??

im just abit worried

thx guys

Link to comment
https://www.sau.com.au/forums/topic/319797-rb26-oil-pressure-drop/
Share on other sites

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

How many litres do you put in the sump?

I put 6l in every oil change with a stock sump. I have seen this happen before, even 3rd gear full acceleration.

Even with the tomei baffle it happens, I'm suprised.

I'm seriously looking at a sump extension to help fix that problem, and a head to sump breather pipe.

6 litres in the sump on change,

im changing the oil on tuesday as its burnt a tiny bit of oil

it was the first time running full synthetic oil after run in

but on the tomei oil pump i left the oil pressure on the lowest setting (ie. didnt add any extra shims)

but where does 6 litres, or the extra litre get you on you on the dip stick? depends on oil cooler setup etc.

it should be on the bottom of the hump on the stick above the H mark.

i too have the tomei baffle but saw oil pressure drop on hard accel with the dipstick on H.

filled it up to the hump above H and no more pressure drop.

hmm, I personally would not be running a tomei pump without an extended sump. check the flow rates for the tomei pump and you will see it can empty the sump pretty quickly... JUN Tomei etc all strongly advise against running their pumps without increased sump capacity.

  • 2 years later...

Hi Guys

As part of my current build I will also be running a Tomei oil pump, ACL bearings (with an extra thou clearance) and sump extension (8L capacity). Unsure of oil weight as yet...

I am interested to know what oil pressure you're reading at say idle, 3k, 6k and 7.5k RPM?

Also those who doing track work what pressure drops are getting down to?

Reason I ask is am trying to figure out with EPC valve to run with Accusump....I found this doc from Canton, see link below:

http://cdn.racerpartswholesale.com/downloads/EPC%20FAQ.pdf

But just want to confirm the 35-40 psi valve is going to be the correct one??

Really unsure at which level of oil pressure (psi) I want the Accusump to open...35-40 psi Or 55-60 psi??

Cheers

i have 100psi at 7500rpm. nitto oil pump and running 20w50 torco sr1 oil.

Thanks mate. Appreciate that. Do you get any oil surge/drops in pressure?

Would be great to hear from others actually using an accusump and what EPC valve you're running...

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
    • Yeah - I mean, go the other way. Smaller range. Not larger.
×
×
  • Create New...