Jump to content
SAU Community

Fs: Nissan R34 4 Door Skyline. P Platers Dream. $14,000 Neg

matty hall
 Share

Recommended Posts

matty hall Apprentice

matty hall

Posted
Posted

Hey guys up for sale is my 1999 R34 Skyline GTV -( was up for sale a few weeks ago but i have to sell due to financial reasons )

Manual

76,000 kms (very low)

Immaculate Condition

Power Steer

Air con

Carbon garnish pillars

Weather shield lips above windows

Factory Floor Mats etc

Cause its the GTV you get all the turbo options minus the turbo... So

LSD

Big Brakes 4 pot fronts and 2 pot rears

Front and Rear Strut Braces

Turbo spec suspension(upgraded again on this car)

Mods:

High Compression 11.8-1 (shaved head)

Adj cam gears

Full Exhaust With Varex Muffler(varible niose levels from remote control)

Haltech Platnium Interceptor with high and low octane maps.

124RWKW

Gates Racing Timing belt and rad hoses

Gab Coilovers

Whiteline 27mm and 19mm Swaybars

Origin Boot lip spoiler

17x9 inch Panasport Rims with brand new Yokohama A-driveR1 tyres

I have some spares that i got with the car that i can throw in.

Don't hesitate to call, very happy to answer any questions.

Located in Sydney NSW.

Contact: 0422 715 683

14,000 very neg.

IMG_3136.jpg

IMG_3147.jpg

IMG_3158.jpg

IMG_3152.jpg

IMG_3160.jpg

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • TurboTapin
      Jacks that fit under GTR lips that can reach the subframe?

      By TurboTapin · Posted

      So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • suko
      J50 clock date suddenly reset to January 1

      By suko · Posted

      Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • Dose Pipe Sutututu
      Chris' Toyota Mark ii JZX110

      By Dose Pipe Sutututu · Posted

      I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • MBS206
      Starter motor replacment teeth count.

      By MBS206 · Posted

      I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...