Jump to content
SAU Community

Is The Exhaust My Car Came With Any Good?

TUF250

By TUF250,
in Engines & Forced Induction

 Share

Recommended Posts

TUF250 Proficient

TUF250

Posted
Posted

Hi folks. I have bought myslef a low k, very clean r33 gts-t manual.

have serviced all the oils, plugs and timing belt and am now ready to start the power mods.

My question is in relation to the exhaust. My car wa imported with a stainless steel 3 inch mandral exhaust. It has two large mufflers on it. the one at the back is slightly larger. They have a JASMA badge on them and K&F i think it was stamped into them? lookign inside with a torch the back one seems to be straight through but has two pipes running through the body but single 3" in and out.

My question is are these any good? do they flow well and not worht changing? the system has a nice note but is very quiet (definately legal!) Any recommended way of getting a little more noise out of it without bringing on drone?

thanks in advance

Jason

TUF250 Proficient

TUF250

Posted
  • Author
Posted

also does anyone have a pic of the standard cat, i think the system has a aftermarket cat on it but it dosnt have a brand on it so i cant be sure.

I want to change the dump pipe to a 3inch unit soon so wondering if its worth doing the cat while im in there

thanks!

lookingforboost Community Regular

lookingforboost

Posted
Posted

when you pull the dump pipe off just take the cat off etra 2 bolts and have a look the inside of it if its still the compliance cat then you wont be able to see light through it or nrealy none and a high flow you should see heaps easy :P

Mine has a 3" system on it a trust cat back with 2 mufflers and its very very quiet but still flows no problems and when on the dyno wasnt a restriction at all so just because its quiet dosent mean its no good.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • AnimalGarage
      spot the stagea

      By AnimalGarage · Posted

      It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • GTSBoy
      R34 Handbrake light saying ON and intermittently flashing

      By GTSBoy · Posted

      Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...