Jump to content
SAU Community

Recommended Posts

On boost is great too.

My 20det on most days would start singing at 2k and make 10psi at 3k, but for everyday driving I found I had to change gears a lot, it bogged down a lot in low revs.

The 25 with r34 turbo starts around 1.9k and 10psi around 2.5k, but even off boost, say 2k through 4k, I can stay in gear without needing to down shift, like going up highway/freeway onramps, stop start traffic, etc. It's much more tail happy too.

It climbs through the revs with a 5kg flywheel about the same as the 20 with a standard flywheel.

I should've just bought this 25 two years ago haha.

Do it man, you won't look back.

  • 2 weeks later...

I hope all you haters are jelly.

vcwcns.jpg

1113uo2.jpg

f0vno6.jpg

Now, stay tuned for fitment of THIS

2s1ofo5.jpg

zlugya.jpg

On teh way in the next container.

Hopefully less hold ups on this one.

Oh and for the record, 25DET still running flawlessly every day, unlike that god damned RB20.

Best thing I ever did getting rid of that dudd.

  • 2 weeks later...
  • 4 weeks later...

Was starting to hear a harsh scraping sound at low speeds, gradually became louder.

First thought was low brake pads/rotors, but then I kind of got my head around the idea that maybe, finally, the shithouse bearings on the JJR hubs had finally thrown in the towel, since they last about 10'000km max.

Brakes were getting a bit low anyway, and I'd already bought pads, so I swapped out my rotors for another set, got mine machined, and after about half an hour of looking around my house, shed, room, and in both cars, I found the brake pads I'd picked up ages ago.

28gtvlu.jpg

Did work at my own house (gravel driveway), and took my sweet ass time.

Was a royal PITA trying to get the pistons in the calipers to retract to fit the new pads over the rotors.

Found the source of that scraping sound too.

5l1dg8.jpg

The other 7 pads were fine, at around 25%

Finished last corner after about 2 hours.

2h560wx.jpg

Ran pads in at local industrial area. They're pretty damn noisy between 15kmp/h and 0, but pedal feels twice as good as it did with standard Sumitomo pads.

JJR wheel bearings are still in tip top condition, 35'000kms and still going strong!

New world record!

Edited by Nic_A31

lol

nick it seems your taking after myself a bit, as you know i did the same to my rears, not too long ago did the same on the front pads!

now the point is to take off my calipers and check them properly at times

whats the deal with these JJR bearings, on paper it says they only last 10,000kms? they better not be pricey to replace

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...