Jump to content
SAU Community

Recommended Posts

Thinking about selling my RB30/26det, its currently in an R32 gts-t four door and making 465hp at the wheels. I've spent a lot of time and money on this car but I don't get time to use it and I'm not dedicated enough to take it to the track anymore. If I use it on the track I'm spending time and money that would be better spent with my 1.5year old and 1 month old girls. However I absolutely love this car, driving it is like nothing else I've experienced. Engine had a freshen up about a month ago when I pulled it out to put tomei oil pump and head oil drain on.

Would like $20k for the whole lot but I'd like to hear offers too

1989 R32 Gts-t

-RB30 Crank

-Precision Rods

-ARP rod bolts

-ACL race bearings

-ARIAS forged pistons

-Tomei oil pump

-Jun crank collar

-4 layer MLSR steel head gasket (could be wrong about brand cant remember)

-1mm head oil restriction and one blocked off

-std GTR cams

-1inch custom head oil drain

-Head ported by Darren at Lewis Engines

-Modified larger sump with head oil drain and catch can inlets

-T04z turbo

-Trust high mount manifold

-Trust waste gate

-Greddy Y intake

-std GTR plenum, inlet manifold and throttle bodies

-800cc SARD injectors

-Malpasi fuel reg

-GTR engine wiring loom (modified to suit car)

-Power FC D-jetro (maps sensors, GTR plug ecu)

-alloy radiator

-FMIC with 3 inch custom piping

-4 liter custom catch can

-Rear mount battery

-R33 5 speed

-5 puk clutch

-Custom one piece tail shaft

-Kazz 2-way diff

-HSD coil overs

-Shortened front upper control arms

-Adjustable caster rods

-R33 GTR V-Spec front rotors

-Alloy pineapples

-Drift Teks 17x9.5 +15

-Nicely streched rear gaurds

-Hicas lock bar (lines removed)

-Nismo or better fuel pump (cant remember again sorry)

-Nardi stering wheel

-Cobra bucket seats

-Drivers Harness

-Hydrolic handbrake

Probably left a few things out. Also have some spares like 25mm spacers and a few wheels like 16's and 17's although some wont fit over the bigger front brakes. Paints not the best but no rust or damage just not matched properly from where the guards have been done and boot holes fixed. I will try and take new pics if I get around to cleaning it. Only pics I have are from back when I drifted it with the RB20. Haven't drifted the RB30 yet but I might if I find some friends to go to a drift practice with. Car can be registered and has been till early this year however there are some things to be aware of with registering a vehicle with an engine like this.

Thanks people

Link to comment
https://www.sau.com.au/forums/topic/321807-eoi-rb3026det-and-car/
Share on other sites

Forgot Apexi AVC-R boost controller and strut brace front and rear. Also power is at 16psi, if you wanted more power all you need is better fuel lines, fuel rail etc and to turn up the boost. 16psi is minimum boost with this waste gate.

  • 4 weeks later...

Happy to sell engine, turbo, gearbox, tail shaft, wiring and ecu as a package. Will bolt straight into R32 Gts-t and should also fit straight into R33 (Not sure about bonnet height tho)

Engine (full engine with all running gear minus power steering pump and air conditioning)

Turbo (on engine with y intake kit and waste gate)

Gearbox (would leave on engine with 5puk clutch)

Tail shaft

Power FC (with map sensors and hand controller)

GTR engine loom with resistor pack for injectors

All sensors, injectors, coilpacks, head oil drain and turbo lines

$14,000

Depending what car it would be going into I also have modified speedo sender and cross member for the RB25 gearbox, inter cooler + piping and radiator and dump pipe Y to waste gate etc.

Hooked up a battery charger today so I can do a compression test if I get time tomorrow. Took a couple pics, needs a clean, lots of dust from it sitting in storage last few months.

post-16618-1277539915_thumb.jpg

post-16618-1277540033_thumb.jpg

post-16618-1277540136_thumb.jpg

Trying to reply to all PM's but I can only send one every half hour for some reason so sorry if I miss one or you don't get a reply straight away.

Did a cold compression test all were between the 125psi and 130psi marks. Car is running but not registered.

  • 2 weeks later...

I've had no serious offers so I'm going to look at parting it out but keeping car so I can sell it cheap later with a RB25det.

First part up for grabs is the turbo kit $3000 for T04z, manifold, waste gate, Y pipe, all lines and S bend (cast turbo to inter cooler pipe).

I thought the compression test was a little low and I just found out why, there is a rubber o-ring missing where the spark plug thread adapter screws on, without it it screws up to far. Also just been told that I should be doing the test hot with all spark plugs out and throttle open which I wasn't doing before so I'll give it another try this weekend.

http://www.skylinesaustralia.com/forums/Rb...Pe-t327866.html

New thread for parting out.

Power FC not sold, got a bit ahead of myself.

Price change to $12,000 ono for complete engine package

Price change to $17,000 ono for full car

Compression test redone, much better, pics attached aprox 150 over all. Engine was about 50-60degrees so not hot but still warm and throttle was held open unlike last time.

Also found video of last event I did, just small mucking around stuff.

post-16618-1278729687_thumb.jpg

post-16618-1278729837_thumb.jpg

post-16618-1278729912_thumb.jpg

post-16618-1278729984_thumb.jpg

post-16618-1278730066_thumb.jpg

post-16618-1278730133_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
    • Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
    • My dream is also to have a proper hoist, but I don't think it will ever happen. My quickjack is probably as close as I'll ever get, it really is very good though. 
    • Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
×
×
  • Create New...