Jump to content
SAU Community

Recommended Posts

The front mount will be fine. Doesn't really have any effect on your emissions.

RED513 is right on the money. Cat and o2 sensor checks and you'll be right to go.

Unless you have drastically changed the amount of fuel (injectors) or air (turbo), then you have no need for an aftermarket ecu. (for emissions, of course. Always power benefits from a tune! :rofl2:)

The front mount will be fine. Doesn't really have any effect on your emissions.

RED513 is right on the money. Cat and o2 sensor checks and you'll be right to go.

Unless you have drastically changed the amount of fuel (injectors) or air (turbo), then you have no need for an aftermarket ecu. (for emissions, of course. Always power benefits from a tune! :rofl2: )

nah only mod is fmic and exhaust had pod but put standard airbox back on

how do i know if the cat thats on there is good enuf

  • 1 month later...

hey guys had car emissions tested and it bombed out real bad so im thinkin of just doing what the tuner said and get the aftermarket ecu but he also said that nistune will not have the paremeters that i need 2 get it to pass

any one know where i can get a power fc

or does any one know anything about microtech as they are in my area and will install 4 1400

nistune and power fc are very similar, just the power fc has more resolution in the maps. nistune will do fuel & ignition, closed loop corrections, after start / cold start and acceleration enrichment, what else do you need to get a good tune to pass emissions. microtech are alright, but its not an ecu i'd be picking, especially for an emissions pass.

Get another tuner! Nistune will tune your engine fine. When you say bombed out on emissions test what was the problem? Do you have any numbers, readout? Did you replace the cat convertor? With an almost standard car its ridiculous to be telling you that you need a Microtech.

Get another tuner! Nistune will tune your engine fine. When you say bombed out on emissions test what was the problem? Do you have any numbers, readout? Did you replace the cat convertor? With an almost standard car its ridiculous to be telling you that you need a Microtech.

ive got a read out here somewhere ill have to scan it and post it and no i didnt change the cat the exhaust place said they only put cats on that meet australian standards and yeah the tuner is saying power fc but i think h just wants to try n make some extra money out of me wants 2 charge me 2500 then tuning on top

try and find out what make the cat is

x-force cats are notorious for their poor performance (both power and emissions wise)

catco and metalcat are supposed to be good tho

and x2 on the nisstune being as good if not better for emissions

have you changed your o2 sensor while you have owned the car? if not, replace it asap its probably the main reason it failed the test cos the ecu can't see how rich its running

Actually a "lean" tune will fail the IM240 test.

The tune must be such that the levels of CO, hydrocarbons, and NOx gasses are all within regulations.

A lean tune will fail just as hard as a rich tune will.

As quoted above, it's not about how filthy rich your tune may be but the gases that are created by the combustion of O2 and fuel.

It is imperative that you have a catalytic converter that is able to convert the gases into other gases that aren't measured in the IM240 test.

This is why decat pipes are illegal and carry a hefty fine for emissions.

hey guys had car emissions tested and it bombed out real bad so im thinkin of just doing what the tuner said and get the aftermarket ecu but he also said that nistune will not have the paremeters that i need 2 get it to pass

any one know where i can get a power fc

or does any one know anything about microtech as they are in my area and will install 4 1400

you know what i think about this bloke man, just get nistune!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • also possibly backed up to my filler and shat down it! 🤣
    • Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
    • What sold me on Trailer Park Boys is this scene: Great stuff, just stay clear from the new Netflix production.
×
×
  • Create New...