Jump to content
SAU Community

Guard Rolling

TonyStarks

By TonyStarks,
in Western Australia

 Share

Recommended Posts

SKYRYAN Grand Master

SKYRYAN

Posted
Posted

I think a guy called Stuart from Dentcraft or something similar did mine, went to his place and he rolled them in his garage.

The funny part was when he put he heat gun down and it melted a hole in the air compressor hose :bunny:

But I've had no cracks or anything in the paint and it seems like a flawless job to me.

Link to comment
https://www.sau.com.au/forums/topic/322234-guard-rolling/#findComment-5255462
Share on other sites
3LGODZILA Proficient

3LGODZILA

Posted
Posted

mate from my old work got his ss's guards rolled by west coast tyres in mandurah. pretty sure he said it cost him $200 and apparently they guarantee they wont crack the paint.

personally i cant see how a workshop can guarantee they wont crack the paint but no harm in asking

Link to comment
https://www.sau.com.au/forums/topic/322234-guard-rolling/#findComment-5256380
Share on other sites
viet_boi Mentor

viet_boi

Posted
Posted

Des from AutoFX, done a couple of my cars, price was $100 - $120 for the both rears depending on what car you have.

Not a single crack or chip in the paint, does it by hammer if needed at the same price too, top work.

Link to comment
https://www.sau.com.au/forums/topic/322234-guard-rolling/#findComment-5256851
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • TurboTapin
      new 1.5 LSD issues/concerns

      By TurboTapin · Posted

      My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • MBS206
      NC MX5

      By MBS206 · Posted

      Bunnings would have just handed you your money back on that one!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...