Jump to content
SAU Community

Recommended Posts

FitzTech and Cefiro...

The import duty is worked out at 15% of the purchase price of the vehicle NOT including shipping. There are further costs incurred with clearing customs (around $150 at last check) but then GST is worked out on the total: Vehicle purchase price, shipping and the import duty (in other words you are paying a tax on a tax - GTS on import duty... I await the comments on that one!). The easiest way to work out your budget (in my humble but experienced opinion) is to convert the purchase price from yen to AUD (I work it out at around 2 yen below the published rate to allow for fluctuations and bank fees), add 15% to this, add around $2,000 for shipping and customs and quaranteen clearance fees, then add 10% of this total to this total. Also, if you didn't already know, only a RAW can actually apply for an import approval so ensure you have one before the vehicle lands at an Australian port or you will have to re-export or destroy it. Then there are the obligatory compliance costs etc as I assume you already know.

DJ984, different importers have their own policies and I cannot speak for any other than myself but I can assume that most would either pay the taxes etc as they arise with your money (how I started), or just pay them themselves and pass the cost on to you. The only other taxes that most importers / consultants wouldn't cover would be the state government stamp duty which is payable upon first registration or on transfer of ownership. These vary from state to state and currently in SA consist of 4% of either the market value or total cost of the vehicle; whichever is the highest (of course).

well htat sounds better than ive been working out. in other words with the permission from the powers that be, a person can import a car and pay 15% customs, the shipping costs, and then 10% on the total of all of the above(of course there are compliance costs etc but i was more concerned about tarrifs). if this is correct cars can be brought over here alot cheaper than alot of people i know think. if sum1 can correct me or can spot a mistake ive made please correct it as im eager to know the low down on importing

check out prestigemotorsport.com.au they have a calculator to work out costs. But as Garage Menace said don't forget compliance $4,500-$8,000 + say $1000 for tyres +$1000 for rego.

But yes, importing directly can be cheaper...as long as you are confident about the quality of the car you have bought

One point I forgot to mention. Some vehicles of a higher value ($40K I think) attract a luxury car tax in addition to the other charges, however only vehicles like the R34 GTR attract this tax.

It has also been tempting in the past to purchase cars that are modified from Japan but the strictness of the RAWS system is making this virtually impossible. The reason for this is that a vehicle must be returned to a completely standard condition before DoTaRS will issue a compliance plate. The RAW then has to destroy all aftermarket parts (they cannot be sold). DoTaRS are rumoured to be conducting random inspections of shipments arriving at various docks and recording VINs as well as the aftermarket parts installed on the vehicles. When the RAW then submits a VIC (Vehicle Inspection Certificate) to DoTaRS in order to be issued with a compliance plate DoTaRS then asks for photographic evidence of the destruction of all the recorded aftermarket parts. I have had many a sleepless night trying to find a way around this rule (and the senseless destruction of perfectly functional and often extremely expensive aftermarket parts) without success (and after witnessing another RAWS applicant being sodomised by DoTaRS inspectors in the past I have no intention of trying to bend the rules - they have more power than police but are considerably more inconsistant and unpredictable; at least you know cops are going to be...). While this may seem to be off the topic of this thread, it is important to consider that compliance costs may be more expensive than anticipated if the RAW has to purchase OEM parts (they cannot be borrowed either as it is illegal for the RAW to re-install aftermarket parts - or even to supply them to the customer - after attaching the compliance plate) to replace aftermarket parts which came with the vehicle. Also, damaged cars (even damaged and repaired) are totally prohibited from being complied so as Duncan suggested, you must trust whoever is purchasing the vehicle for you in Japan. Otherwise when the RAW refuses to comply a vehicle you have imported you end up with a very expensive mistake as you must either re-export or destroy the vehicle and you cannot just take the vehicle to another RAW. DoTaRS will only issue a compliance plate to the RAW named on the import approval.

If this info has been posted somewhere before... Sorry. Otherwise, good luck.

2 Questions... (sorrie if this has been raised before)

1. If the vehicle in question is a personal import, what kind of duties are imposed(and how much)?

2. As a personal import is the vehicle still subject to compliance rules that that state the vehicle must be stock standard?

Thank you!

That's a good question and one that will require some research before I answer as I have never dealt with personal importing (I am sure someone on these forums will know though). I assume (you know what they say about assuming though) that the import duties would remain the same however the compliance rules are slightly different, but the main advantage is that you can bring in vehicles that are not available under SEVS. Unfortunately though, a couple years ago the Federal Government increased the length of time a person had to own a vehicle at it's country of origin before it could be exported to another country from 3 months to 12 months. To me, not worth it unless you already live in Japan and have owned the vehicle for the required length of time.

I will get back to you with a definitive answer soon.

Cheers all.

Yes, Personal Imports attract the same duties, GST and other costs of importation, but compliance is relaxed.

However, as mentioned, you have to own the vehicle for 12 months first, and this includes:

- living in the same country as the vehicle for 12 months and being able to prove it

- actually driving the car for 12 months and being able to prove it by showing parking receipts, insurance paperwork, servicing receipts with mileage etc, blah blah blah

They are extremely tightarsed and I've had a problem or two with this in the past when importing BMW's from the UK.... It's not fun.

Good luck.

Simon.

  • 9 months later...

So if i bought say an R34 GTR and lived in Japan for a year driving it around and then decided to come back to Australia and bring it with me... could i say i paid $25,000 for it so that i pay less duty and GST and i avoid the luxury tax as well? or will they basically tell me to get ****ed and work it out on market value here?

Cheers,

Andrew

So if i bought say an R34 GTR and lived in Japan for a year driving it around and then decided to come back to Australia and bring it with me... could i say i paid $25,000 for it so that i pay less duty and GST and i avoid the luxury tax as well? or will they basically tell me to get ****ed and work it out on market value here?

Customs would require some sort of proof of what you paid for the car, eg an invoice. But they have various methods of working out the value, see here:

http://www.customs.gov.au/site/page.cfm?u=4371

also take into account that if your car lands in australia AFTER 1st Jan 2005 then you only have to pay 10% duty as per the new rule. But don't expect it to save you a fortune, just enough to fund some intake mods :)

ive got an r32 GTR coming over next month on 15 year rule how much will it cost me at the docks to clear the car and pay for the shipping, gov stamp duty etc geoff from prestige motorsport told me about $5800 but im not sure if the gov. stamp duty etc. is included in the price, ive tried calling him for a few days now but not geting any luck. ive organised SRICAR in melbourne to do the complience and there charging $1000, thats the cheapest place ive come across yet. ive tried using prestige's cost calculator but its to confusing. can any one help me

ive got an r32 GTR coming over next month on 15 year rule how much will it cost me at the docks to clear the car and pay for the shipping, gov stamp duty etc geoff from prestige motorsport told me about $5800 but im not sure if the gov. stamp duty etc. is included in the price, ive tried calling him for a few days now but not geting any luck. ive organised SRICAR in melbourne to do the complience and there charging $1000,  thats the cheapest place ive come across yet. ive tried using prestige's cost calculator but its to confusing. can any one help me

you may have to expand on this a little more,

like if you've payed the FOB price, prestige's service fee, anything else?

providing you know the price you payed for the 32 gtr you should be able to give you an idea.

say you payed about.....$10000 - $12000 (aud) for the GTR then $5800 for govn't tax and stampduity and otherstuff that i carn't remember now sounds about right.

"FOB price + Import broker's service fee + 15% to this, add around $2,000 for shipping and customs and quaranteen clearance fees, then add 10% of this to the total."

above was pretty much a cut and past of Garage Menace's origional post.

Well my initial estimate from prestige was pretty much dead on, up to about $50..

Here is the breakdown I got from customs the other week:

Duty : $979

Freight: $882

Port Service Charges: $155.85

Delivery Order: $45

Quaranteen Fee: $203.50

Quaranteen Attendance: $95

Cartage: $75

Postage & Petties: $12 (their lunch that day :rofl:)

Agency: $150

Documentation: $35

Redline: $45

==

Sub Total: $2678.30

GST: $61.29

Total: $2739

Original FOB price + Agent Fee was $4500 .. so you are paying about 25% of the original purchase price on duty I think in the end.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Any update on this one? did you manage to get it fixed?    i'm having the same issue with my r34 and i believe its to do with the smart entry (keyless) control module but cant be sure without forking out to get a replacement  
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if something was binding the shaft from rotating properly. I got absolutely no voltage reading out of the sensor no matter how fast I turned the shaft. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if shttps://imgur.com/6TQCG3xomething was binding the shaft from rotating properly. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
×
×
  • Create New...