Jump to content
SAU Community

Adjusting Wastegate Preload On 3076 Iw

gwilkinson34
 Share

Recommended Posts

gwilkinson34 Collaborator

gwilkinson34

Posted
  • Author
Posted
All the internally gated turbos I have seen/used have some adjustment in the length of the actuator rod.

Cool cool.

I assume this is not the sort of thing I should just play with and 'see how it goes' but rather stick it on the dyno?

gwilkinson34 Collaborator

gwilkinson34

Posted
  • Author
Posted
what do you want to achieve ?

Just to see if it helps bring the boost on a little faster - looks a little lazy coming on... The other side of it is playing with boost controller gain etc.

If it's something I could do myself without a big $$ outlay on dyno time (as i've just forked out a crapload to get here!) then i might play with it. If it's a bad idea to do it by the seat of my pants dyno / boost gauge then i'll wait till i do something else on the dyno...

post-71984-1275542484_thumb.jpg

l0WRB Mentor

l0WRB

Posted
Posted

adjust little bits at a time, take it for a drive.. but ur going to need to turn ur settings down on the boost controller, as making it tighter/harder to open is going to want to raise the boost level.. so turn gain down etc

Crans Mentor

Crans

Posted
Posted

Turn boost controller off take it for a run not when you hit max boost.

Adjust arm length a tiny bit and go for another run and not when max boost it ( boost will likely increase as well)

Keep doing that until you get no more gain but be careful your not over boosting.

When you have found the sweet stop user boost controller to hit desired boost.

gotRICE? Veteran

gotRICE?

Posted
Posted (edited)

Are you using the actuator that came with the turbo?

They arent the greatest, quite soft and creep open a bit, that's probably causing the slow boost.

I got one for a mate for his 3076 from USA, 14psi spring. The overall size was larger, and it was tight as buggery compared to the "stock" actuator. (when doing the old "pull on this" trick) :blink:

PM "Lithium" and ask him a question or two. Hes tried a few different approaches to the spool issues.

Edited by gotRICE?
gwilkinson34 Collaborator

gwilkinson34

Posted
  • Author
Posted
Are you using the actuator that came with the turbo?

They arent the greatest, quite soft and creep open a bit, that's probably causing the slow boost.

I got one for a mate for his 3076 from USA, 14psi spring. The overall size was larger, and it was tight as buggery compared to the "stock" actuator. (when doing the old "pull on this" trick) :blink:

PM "Lithium" and ask him a question or two. Hes tried a few different approaches to the spool issues.

Boost controller is a Greddy profec II spec B (or whatever it's called).

I 'asked' the place that built my car to get the larger actuator on the 3076 as apparently it comes standard from Garrett... I can't seem to move the rod at all by hand...? (and i'm not a small dude)

There is a thread on the rod, so could turn off the boost controller as suggested and see what tightening or loosening it does...?

JonnoHR31 Grand Master

JonnoHR31

Posted
Posted

to add more preload to the gate wind the road so that the overall length is shorter. only do it a few mm at a time tho. once you have enough preload to keep the gate shut properly use the profec to bring it on earlier by slowly increasing the gain and start/set boost until it spikes then back it off a touch. if you want 18psi i'd start with a set boost of 14-15psi and wind the gain up.

this will change the torque around that area. ideally you should get the tune checked around that area but if you dont want to do that just keep a close eye on your knock levels (if possible) whilst adjusting the boost.

gwilkinson34 Collaborator

gwilkinson34

Posted
  • Author
Posted

Well here's an advertisement for not always taking dyno readings as gospel - I did some testing on the road on the way to work this morning - it's kind of hard to tell exactly since i can't use WOT in 2nd as the back goes by 4500rpm or so but i was making over 1bar by 4000rpm and was definitely at the full 18psi well before 4.5k. At which point i was going sideways down the road and had to back off... :blush:

I assume the tuner didn't plant his foot on the dyno from down low and this is why it looks lazy onto boost on the chart...?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

      Waaay ahead of ya....(evil laugh!!) Will show the fitment and spec details later when it isnt as rainy !
    • wizlb
      Flex Fuel Kit Workshop

      By wizlb · Posted

      Thanks Dose.....    I appreciate it!!
    • Dose Pipe Sutututu
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Dose Pipe Sutututu · Posted

      I'll probably be putting the shit box back on the dyno again soon, I want to dial in the closed loop boost control properly. I'll have a camera facing the car/motor for fun too. Just note, there are essentially 3x 10AN inlets going into the catch can and 1x going back to the intake pipe. Most of the time the catch can "return" to the sump actually is the crank case breather, pushing air out.
    • Piggaz
      Ogura orc1000f vs Osg tr2cd vs Osg r3c experiences, max torque/max hp?

      By Piggaz · Posted

      I have the R3C with a Nismo slave and by no means does it behave like a stocker, it ain’t THAT bad. On take off just give a bit more throttle than you would say a coppermix and it’s fine. It will not slip though.   
    • uchoa
      Yet another RB Neo misfiring thread after reading all the others.

      By uchoa · Posted

      Okay. Final round of testing done. Got a friend to hook up a fancy scanner to the car and we also ran some compression and leakdown tests, she is healthy.  The MAF was definitely the culprit. So for future reference anyone with similar issues that find this thread. I suggest the following steps, in order of affordability:   Check your spark plugs for any fouling, replace plugs if they are bad or re adjust the gaps making it narrower (0.8mm would be good). Check every coil's resistance with a multimeter. It can be done by probing the IB and G pins on the coil pack. Resistance should be around 1.4 (+/- 0.1) Ohms Check the MAF. If you have Nissan connect or a good scanner with the 14 adapter it should allow you to see the voltage on the MAF reading should be around 1.1 - 1.2V when car is idling. But if you don't, buy a new MAF from Amazon and test, then return it. (For instance, I got a Chinese one for $40 that was reporting 1.3v on idle). If you still have scanner, you can run tests on the injectors to see if they are working, just remember to unplug the fuel pump fuse/relay and have no pressure on the line. Then listen for the noises that the injectors make. Clean/replace injectors as needed. Once you find the issue and fix, order thousands of dollars worth of OEM parts to refresh unrelated things (Optional)   PS: Thanks to the absolute legends of this forum for the responses and help to someone that went a bit over their head. (me)
×
×
  • Create New...