Jump to content
SAU Community

Recommended Posts

You need to cancel your current rego on the car in VIC, and whoever you're swapping your car with, they need to have it re-registered in NSW.

That involves, Blueslip, Greenslip, and a engineering cert if you have engine mods (the blueslipper will pick up on this during inspection)

Edited by Owens

Correct. You can transfer your rego into someone else's name in the same state as you, or transfer your rego into your own name interstate, but you can't do both.

As said, you will need to de-register the car and the new owner will need to go through the whole registration process from scratch.

also, just because you may be swapping cars (with no cash changing hands) you will both still need to pay stamp duty on the value of the car. Can't have the government missing out on its well earned revenue, now can we?

thinking about swapping my car with someone in sydney & i live in victoria, i need to get it roadworthy, does a victorian roadworthy certificate cover NSW? or do i have to travel to NSW & get a roadworthy done?

well most important to keep old rego much ezyier to swap over. then if the car is import then is more trouble there as well aspecialy if is imported under more then 15 yold rule what means u need engeniring certificate in each state as all difrent rules :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Some troubleshooting, connect up a timing light/gun with a proper ignition lead on coil 1. Hold the revs at 4~4500rpm and see if your timing is all over the shop, scattering off its tits. If so, there's a high chance your CAS is fked. But I read you have a Link ECU ready to go in, why not just skip all this and put that in - will make troubleshooting so much easier.  
    • Misfires when the car is fully warm are generally attributed to the coils (and/or the igniter, on cars with a separate igniter). They can stop working properly when they get hot for a number of reasons. Either electric/electronic, or from thermal expansion opening up gaps and allowing HV leakage. Seeing as you have replaced the coils, that could/should rule them out. But I wouldn't always assume so. Were the coils genuine? Or is there a chance you have bought some counterfeit Chinesium shit? Then we're back onto loom connections. They can fail when warm/hot for the same reasons. Inspections, cleaning of contact surfaces, ensuring that terminals are fully inserted, etc etc, are all justified. The same (heat effects) holds true for the other electrics and their connectors. AFM & CAS, primarily. If you try that Chinesium AFM, drive it around on low load until it is properly hot, but do'nt give it more load than you have to, except when you need to see if it will still miss. I'm dead serious about the untrustworthiness of the calibration of those copy AFMs. Injectors are unlikely to get hot unless the fuel is coming back around hot. You could try squirting them with compressed air or freeze spray to cool them back down to see if they are maybe the cause.
    • Alright, all the plugs looks good. Noticed that it starts to get bad when the car is up to temp, that's when things starts to misfire hard. next to do is Injector cleaning and such. Got in touch with a shop to do work on the injectors next Monday also help on diagnosis.
    • House of Fatz dry dock needs a clean sadly one of the long time stables is leaving this weekend   see ya mr purple
    • Hence why I've only modified my car into a pure daily. Everything has to remain reliable & roadworthy, while providing value and grin factor. It also must not be handcrafted to the extent that the car will be immovable if something breaks because you cannot get or make a replacement to at least limp around with.
×
×
  • Create New...