Jump to content
SAU Community

Air Bubble In Atessa Resevior

Simonster
 Share

Recommended Posts

Simonster Proficient

Simonster

Posted
Posted

Hi,

I have noticed recently when turning on the ignition, an electric pump (not the fuel pump) underneath the back of the car ran for a second or so. The time it ran for slowly increased so i checked out the atessa reservoir. It seems to have a section towards the bottom where there appears to be an air gap.

I gather this is what it is, and the filter may have something to do with that.

When you look at the reservoir the oil level is fine but there seems to be an air-gap towards the bottom of the tank.

Is there anyway to remove the top of the reservoir and take out the filter??

Any guidance is appreciated.

Link to comment
https://www.sau.com.au/forums/topic/324508-air-bubble-in-atessa-resevior/
Share on other sites
  • 2 weeks later...
Simonster Proficient

Simonster

Posted
  • Author
Posted
Pretty much mine has a 4mm air bubble around, think that's normal

Ah ok. I suspected that it was a problem cause when i turn the cars ignition on, I can hear a motor running for a short period of time, i gather its getting the atessa up to pressure. That motor is running for longer now, around 4 seconds whereas a number of months ago, it made no noise at all.

That's why i thought the air bubble was not normal.

So what would cause this motor to run- low fluid. I've checked the leves and they are fine?

Thanks

Beer Baron Grand Master

Beer Baron

Posted
Posted

attesa pump always should prime for a few seconds when you turn ignition on. many people mistake it for fuel pump priming but in a standard-ish GTR (with say bolt in nismo pump or standard pump) the attesa pump primes much louder than the fuel pump. approx 4 seconds sound normal to me.

Simonster Proficient

Simonster

Posted
  • Author
Posted
attesa pump always should prime for a few seconds when you turn ignition on. many people mistake it for fuel pump priming but in a standard-ish GTR (with say bolt in nismo pump or standard pump) the attesa pump primes much louder than the fuel pump. approx 4 seconds sound normal to me.

Great thanks Richard, i appreciate it! :whistling:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      PXL_20250828_063541093.TS.mp4
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • PranK
      R35 GT-R production ends after 18 years

      By PranK · Posted

    • SteveL
      Leak from Tokico BM50 Brake Master Cylinder

      By SteveL · Posted

      I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...