Jump to content
SAU Community

Recommended Posts

hey guys,

i recently bought a turbo tech manual boost controller off ebay, and loosened the screw all the way (0.7bar), however when i have the boost controller installed, my car develops a big misfire...

Is there any obvious cause for this?

mods: bosch 040, turboback exhaust, pod

Link to comment
https://www.sau.com.au/forums/topic/324825-t-piece-boost-controller/
Share on other sites

I would say 10 PSI and no tune = BAD

Restrictive exhaust would not help and the manual boost controllers are known to spike so could be way more boost and leaning out. (Not a big fan, better to use electric one)

You realy need a tune before you do damage.

You pretty much answered the question yourself "missfire". A missfire is a poor spark, so either your spark plugs need replacing or your 15 year old coilpacks aren't up to the job anymore, or both.

Edited by PM-R33
I would say 10 PSI and no tune = BAD

Restrictive exhaust would not help and the manual boost controllers are known to spike so could be way more boost and leaning out. (Not a big fan, better to use electric one)

You realy need a tune before you do damage.

it wont be running lean. more boost sends things rather rich with the stock ecu and turbo.

as PM-33 said, poor spark. i'm assuming its under full load around 4500-600rpm? if so the most likely culprit are tired coilpacks. can try taping/siliconing them or get new ones. in the meantime you can gap your plugs down a bit.

have a search around here, theres countless threads on this

hey guys thanks for the replies,

i have recently just replaced my spark plugs gapped to 108mm, i sussed out the coil packs and there are no visible hairline cracks etc.. in them.

With the stock boost solenoid, with the exhaust my car runs 7psi <4500rpm, then above 4500rpm it goes to 10psi... and starts to 'misfire' when its on 10psi.

also cleaned the A/F meter, replaced the fuel filter, air filter and reset the ECU.

Edited by shaun123
hey guys thanks for the replies,

i have recently just replaced my spark plugs gapped to 108mm, i sussed out the coil packs and there are no visible hairline cracks etc.. in them.

With the stock boost solenoid, with the exhaust my car runs 7psi <4500rpm, then above 4500rpm it goes to 10psi... and starts to 'misfire' when its on 10psi.

also cleaned the A/F meter, replaced the fuel filter, air filter and reset the ECU.

the coils may look ok, but may not be ok. try taping them up with electrical tape and see if that helps at all, but my guess is that you'll be up for new coils.

Leave your coil covers off and run the engine at night in the dark.

Enjoy the electrical storm.

Id be testing plugs regapped to 0.8mm first though, before you put the coil covers on have a look for sparks arcing around the coil packs.

I also run a smear of dielectric grease on the ends of my coil packs to help stop spark loss on both my GTR and XR6.

had the same issue.

Fixed by gapping the plugs to 0.8. Also smeared a thin layer of high-temp silicone gasket-making crap around the square block part of each coilpack (theres a thread somewhere in the DIY section), since I had them out anyway.

gap plugs then put it in 5th gear at 50kph then floor it. if it missfires then it will missfire badly under this load and its gona be your coilpack. just spend about $250 bucks on a set of heavy duty dsr coils. they are some of the best

gap plugs then put it in 5th gear at 50kph then floor it. if it missfires then it will missfire badly under this load and its gona be your coilpack. just spend about $250 bucks on a set of heavy duty dsr coils. they are some of the best

This sounds like an excessively bad way to diagnose the issues sure it might work but the strain on the motor/gearbox would be stupid. 50kph in 5th and full throttle lol

This sounds like an excessively bad way to diagnose the issues sure it might work but the strain on the motor/gearbox would be stupid. 50kph in 5th and full throttle lol

Its actully what the mechanics do to try help diagnose the problem. Probly the least stressfull on the engine as well. How would it be more of a strain at 1500 rpm then at 4500 rpm? Takes you about a second to find out how badly its missfiring. And then you can fix it. Unless you want to continously thrash your car finding out how badly its missfiring. And pretty sure it wouldnt have a problem with the gearbox. How would it?

heavy duty dsr coils? what are these? (other than a crapload cheaper than splitfires and yellow jackets)

I got them off trademe coz im in NZ and my mate has them in his 25det gts4. My engine runs absolutely perfect and i wouldnt have anything else to be honest. Nothing is going to out perform them for how much power i have. PLus they are like 400 bucks cheaper then yellow jacket and stuff lol

no, you are correct. stock turbo @ 10psi on stock ecu is fine 99% of the time. there will be the odd car that will hit rich and retard at this level, but very few, and this can come down to innacuracy of the boost gauge (may be reading 10psi but the car is actually boosting 11 or 12psi)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...