Jump to content
SAU Community

Recommended Posts

hey all, my r32 with rb20DET is getting harder to start, i have to pump the accelerator to get it to start, when its warm its fine, any ideas? btw plugs have been regapped to 0.8, ive got a fmic, HKS evc, apart from that its stock as a rock.

theres a cold start valve on the r33. i think the 32 has one, and its easier to access. that could be your problem. it opens up to allow more air to the intake until it gets warm, then shuts.

if your idle is steady once started, i would assume your aac valve is working ok.

well thats what i thought lol, guess it just needs more air??, had a knock sensor trouble code and it just sounds normal when starting, cant really describe any odd sounds, just my fuel pump turning on and it cranking lol

theres a cold start valve on the r33. i think the 32 has one, and its easier to access. that could be your problem. it opens up to allow more air to the intake until it gets warm, then shuts.

if your idle is steady once started, i would assume your aac valve is working ok.

really???? most cold start setups are richer.

check that the TPS is setup correctly

hold on. do you mean pump your accelerator before cranking it? or when you start it, it needs gas to bring the revs up or it stalls?

hey mate my car has being doing this. If i don't pick the revs up to about 1500rpm as soon as I start it it will stall any ideas what is causeing this only happens when the car is cold.

Just a thought, but could it be over fuelling? maybe almost flooding of sorts. I know whenever I rejetted a carby & went too far I would have to hold throttle open-not an efi I know but you have changed the amount of fuel going in it may be messing with cold start map

Ive had this problem with my 32 and my main factor was the afm ( air flow metre ). Its running good now besides from the pumping of the gas when car is on, try the AAC valve, give it a clean, its located at the back of the plenum near the firewall kinda, cant miss it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
×
×
  • Create New...