Jump to content
SAU Community

Recommended Posts

hey

just bought a set of volk gtc's for my r33 gtr. got them home and realised i need a set of different nuts for them.

where am i able to find these specail nuts, and hub rings for them and is there anything else i may need to fit them?

thanks

Link to comment
https://www.sau.com.au/forums/topic/326042-gt-cs-on-a-gtr/
Share on other sites

youll be the second silver 33r with gt-c's in adelaide then (havent seen any others yet). heres how dope theyll look once you get em on...

The_GTR_by_smellygruby.jpg

the standard volk nuts mine came with are 12x1.25mm internal hex drive nuts. youd probably be looking around the 250-300 mark for a set. on the other hand if you already have some nuts, see if a place like wheelworx can machine them down to correct diameter.

Link to comment
https://www.sau.com.au/forums/topic/326042-gt-cs-on-a-gtr/#findComment-5310872
Share on other sites

youll be the second silver 33r with gt-c's in adelaide then (havent seen any others yet). heres how dope theyll look once you get em on...

The_GTR_by_smellygruby.jpg

the standard volk nuts mine came with are 12x1.25mm internal hex drive nuts. youd probably be looking around the 250-300 mark for a set. on the other hand if you already have some nuts, see if a place like wheelworx can machine them down to correct diameter.

The profile looks too high on the front..

Link to comment
https://www.sau.com.au/forums/topic/326042-gt-cs-on-a-gtr/#findComment-5311435
Share on other sites

The profile looks too high on the front..

That's coz it is. Took that pic just after I put the coilovers in ans the backs were too low. Ideally I wouldve lowered the fronts to match but that would make it too impractical as a daily. Since that pic ice raised the rears so the stance is even now

Link to comment
https://www.sau.com.au/forums/topic/326042-gt-cs-on-a-gtr/#findComment-5311747
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Pads for R32 GTS-t, R32 GT-R non V-Spec (Sumitomo), R33 GTS-t and R34 GT-t are all interchangeable. R34 GT uses a 2x piston caliper, hence it didn't fit.
    • Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
×
×
  • Create New...