Jump to content
SAU Community

Recommended Posts

R33GTR Vspec '98 RB31DETT 716hp/534kw 970nm at 20psi No injector left, HKS GTRS's, E85

E85 Steve!

that is rude!!! 534kw!! RB31 and GTRS's! just spastic....

is that 534awkw?

i would like to see a tear down of a motor after it's been running E85 for a while though.

Before i made the switch, we did a compression test just to make sure everything was ok, Trent @ Status said it was near perfect across all 6 - got a test done last week after about 18months on E85, 170,168,168,165,168,170 - don't know if that tells us much but my engine sure is still in tip top shape - i reckon the E85 has helped it stay in very good condition, oh and the tune of course :whistling:

  • Replies 91
  • Created
  • Last Reply

Top Posters In This Topic

Out of that report;

The E85 fuel is made to a world standard and 70-85 per cent ethanol.

I don't like the sound of the bit that's highlighted;

The Flex Fuel cars change their maps according to a sensor in the tank that tells the ECU what Ethanol content the current batch of fuel has.

We don't have that luxury, if we tune our cars on say E72 batch fuel and the next batch is E84 or vice-versa we'll have problems.

Just remember that the fuel in the main stream stations is designed for FLEX-FUEL cars; and they don't guarantee an Ethanol percentage as the cars it's designed for do need a set percentage, But we do.

I'll be getting mine for Scotchers when i swap over.

Edited by D_Stirls

I've tried lots of combinations of mixture's, e50-e85, tune doesnt change that much that you'll have to worry, does richen up a little the more 98 you run but does not make any difference to the knock protection ethanol offers, power drops off a little, I doubt you would notice you were running e70 once your idle settled!

Ill be sticking with united CSR.

Powerplus E85 is the best if you can get it.

We have 1 United and 1 Powerplus here. I've had tunes on both, as has joeyjoejoe, and both of us had to get Status to fiddle with the tunes (even though both are E85) but Trent said both times the Powerplus fuel was better. It has a slightly higher ROn rating as well.

Powerplus E85 is the best if you can get it.

We have 1 United and 1 Powerplus here. I've had tunes on both, as has joeyjoejoe, and both of us had to get Status to fiddle with the tunes (even though both are E85) but Trent said both times the Powerplus fuel was better. It has a slightly higher ROn rating as well.

Yeah we dont have Powerplus here, so for months now, the only available E85 on pump is Tapleys Hill Rd United. Other than that, Scotchers race fuel.

Powerplus E85 is the best if you can get it.

We have 1 United and 1 Powerplus here. I've had tunes on both, as has joeyjoejoe, and both of us had to get Status to fiddle with the tunes (even though both are E85) but Trent said both times the Powerplus fuel was better. It has a slightly higher ROn rating as well.

I'd like to play with this powerplus, maybe get some feedback on how it's going long term, I've had problems with filters blocking and pumps getting destroyed when running non CSR E85.

What are people doing about engine oil, is there anything specific that you would need to use? Also, I have heard mixed information about E85 being harder on valve guides and also water vaopur in exhausts.

I've tried lots of combinations of mixture's, e50-e85, tune doesnt change that much that you'll have to worry, does richen up a little the more 98 you run but does not make any difference to the knock protection ethanol offers, power drops off a little, I doubt you would notice you were running e70 once your idle settled!

Ill be sticking with united CSR.

Have you been able to check the difference between E50 and E85 on a dyno? Or is this just seat of the pants?

Light knock etc is very hard to notice at WOT

I tried 50% mix long time ago to try keep my injector duty down, didnt run back to back on dyno, but it was still making insane power on the dyno at 50%, noticed more on the rd, lost response mainly. I've never had any knock register (on the sensors anyway) running e50, e75 or e85, I havnt explored the timing limit's either. 5-7 degree's across the map works well for me! some start at 15 and go from there, I'm happy not to push my 14 year old engine beyond 600 ish rwhp :)

I tried 50% mix long time ago to try keep my injector duty down, didnt run back to back on dyno, but it was still making insane power on the dyno at 50%, noticed more on the rd, lost response mainly. I've never had any knock register (on the sensors anyway) running e50, e75 or e85, I havnt explored the timing limit's either. 5-7 degree's across the map works well for me! some start at 15 and go from there, I'm happy not to push my 14 year old engine beyond 600 ish rwhp :)

pfffft whats wrong with ya mate. go for 750rwhp that where its at ;)

re: oil - 'apparently' the full ester oils like 300V chrono etc are not recommended with E85 - Motul is meant to be having a compatible oil, but not release for a while.

Gulf Western's GRoup V oil says it's ok to use with Ethanol... so i don't know what the go is.

For the time being, i go with the Yank oils, Royal Purple or AMSoil (what i've currently been running, 10w40) as i know they're ok with ethanol. They've had ethanol for longer, so i'm sticking with US products so far.

If we had some Brazilian contacts, we could probably get everything answered :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The team at OBD2 Australia are pretty good, shoot them an email and ask them. I've dealt with them before for work stuff. I'd be shocked if it didn't work, so long as Consult can activate the ABS. But you might need to use KLine for it which would be the stopper, as I don't think that piece does KLine comms.
    • Yeah and hence my ghetto way of slamming the brakes, get the ABS to cycle, rebleed seems to be a sensible workaround.
    • Hey! Happy to help. Nothing inherently wrong with the adapter, it's more so with Brett Collins himself. He gave me a lot of incorrect information when I was in contact with him and was extremely rude when I challenged him. He stated I could not use any aftermarket twin plate clutches except for his own, not to use the dush shield, bla bla bla and it was all BS.  Collins stated to cut roughly 14mm's off the housing, I took off 15mm to make room for the dust shield. I would confirm with whatever adapter manufacturer you're using. 
    • There's plenty of OEM steering arms that are bolted on. Not in the same fashion/orientation as that one, to be sure, but still. Examples of what I'm thinking of would use holes like the ones that have the downward facing studs on the GTR uprights (down the bottom end, under the driveshaft opening, near the lower balljoint) and bolt a steering arm on using only 2 bolts that would be somewhat similarly in shear as these you're complainig about. I reckon old Holdens did that, and I've never seen a broken one of those.
    • Let's be honest, most of the people designing parts like the above, aren't engineers. Sometimes they come from disciplines that gives them more qualitative feel for design than quantitive, however, plenty of them have just picked up a license to Fusion and started making things. And that's the honest part about the majority of these guys making parts like that, they don't have huge R&D teams and heaps of time or experience working out the numbers on it. Shit, most smaller teams that do have real engineers still roll with "yeah, it should be okay, and does the job, let's make them and just see"...   The smaller guys like KiwiCNC, aren't the likes of Bosch etc with proper engineering procedures, and oversights, and sign off. As such, it's why they can produce a product to market a lot quicker, but it always comes back to, question it all.   I'm still not a fan of that bolt on piece. Why not just machine it all in one go? With the right design it's possible. The only reason I can see is if they want different heights/length for the tie rod to bolt to. And if they have the cncs themselves,they can easily offer that exact feature, and just machine it all in one go. 
×
×
  • Create New...