Jump to content
SAU Community

Recommended Posts

  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Bit quick on the "harrassment" trigger that buddy...

If it's on the manufacturer's tyre placard as 670 load rating or higher, I don't see that as being harassment.

Instead, I have to question Nissan's motive for putting such a high load rating for the car.

Really wouldnt cops have better things to do than hassel james about something as pity as this? Y not catch someone who is breaking a law

Bit quick on the "harrassment" trigger that buddy...

If it's on the manufacturer's tyre placard as 670 load rating or higher, I don't see that as being harassment.

Instead, I have to question Nissan's motive for putting such a high load rating for the car.

A bit quick but ultimately im right and you know it. :D

The tyre placard was placed on his car by an imbecile.

Although I think it's being incredibly nit-picky, technically a law has been broken.

How many times do you cross a street not near a crossing a week? That is technically jay walking so you should be fined for each time you do it, but u wont coz it a :bs!: law 99% of the time.

Don't misconstrue what I've written INASNT. James was picked up on a technicality because he's done most of his modifications legally. I'm not condoning the action of the Police officer, but if he's been told to come down hard on imports by his superiors, then he is simply following orders.

Don't misconstrue what I've written INASNT. James was picked up on a technicality because he's done most of his modifications legally. I'm not condoning the action of the Police officer, but if he's been told to come down hard on imports by his superiors, then he is simply following orders.

Victoria has been ***ed up since steve bracks became premier. If u lived here you would know that 95% of the canaries the cops hand out here are bs, especially on imports. Its all about the $165 fine they give you for driving a modified vehicle they care about, even worse now coz the fault revenue raising speed camera are not operational for atleast another month coz the vic government was in such a rush to make extra $$ they went out and bought cheap faulty cameras which cant even be sent back to their manufactuer to be repaired as the manufacturer has gone broke!!!

It really pisses me off when cops pick on pety things like this when theres so much crime going on elsewhere that they do nothing about. U are better off being a criminal in victoria, u will get hasseled by the cops less.

Rant over.

Have just been to see Dean at UPI - and now have a 'new' placard that states 600kg as a minimum. Also visited Ice - and took photos of the placard on the GTRs there: 1 was for 600kg, 1 was for 580kg (R34 GTR).

As NRB said - technically, these tyres were illegal for my car. It just so happens that it might have been the placard that was wrong, and not the tyres - but I didn't know that, and I wouldn't have expected the police to either.

The officers involved have all been very helpful - it's their job to inspect cars. Sure, they didn't inspect anyone else... but still. The lead officer was actually concerned that he made a mistake - as the 93 index is pretty high. His XR6-Turbo had 615kg tyres on it, and I'm sure there' snot that big a weight difference between the cars. Hell - with all the pursuit gear, his may be heavier than mine!

What it would seem though - is the placard on my car is the exception to other cars. I will present my case to VicRoads - showing that most GTRs are asked to be above 600kg, some above 580kg - and my tyres are rated at 650kg.

I'll keep you posted on how I get on.

Also - once this is sorted, I'll fit the 600kg placard to the car (it states it's for an R33 GTR, whereas mine does not) - so this never happens again :D

But... I guess it's something to be mindfull of.

Thanks again all for your help.

Well... I can't really complain about anything.

They inspected my car as they are being told to do.

The sticker said 670+, my tyres said 650 - therefore, defect.

Sure it's a pain, but they are doing their job.

At the end of the day, the police weren't wrong about the tyres, the sticker is wrong. If I had been running tyres that were grossly under the vehicle's weight rating, it could be very dangerous.

I wont pay a fine but I also wont get the hours of running around trying to sort this out credited to me.

I WILL write a letter to Stonnington TMU - detailing what happened, but more as an informative note so they know for future reference. The real complaint is to VicRoads for not having a standard placard for GTRs. And they'll be getting a letter too :D

Dude thats bullshit.

93 is 650kg x 4 = 2600 kg

Your GTR does not even come close to needing tyres with a higer load index. This is harrassment and you should file a complaint.

Well what happens when you go around a corner quickly? I'd say there would be a lot more load on the tires when you go around a corner.

What if cornering hard and hitting a pot hole... ouch... I can see the reason for the high requrements, Just covering their asses for the worst.

And i haven't mentioned towing either :(

Well what happens when you go around a corner quickly? I'd say there would be a lot more load on the tires when you go around a corner.

What if cornering hard and hitting a pot hole... ouch... I can see the reason for the high requrements, Just covering their asses for the worst.

And i haven't mentioned towing either :)

:(

go and read the thread before commenting.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...