Jump to content
SAU Community

Recommended Posts

Dont know if this is relevant, but my c34 does that on occasion, boost it normally runs is 11psi but sometimes it wont go past 7, turn it off wait a few minutes and its back to normal, I believe in an older thread you guys said this was something to do with the fact that stags run 7psi out of the factory and a computer hicup can cause it to limit itself to factory boost temporarily or something along those lines? So if your running an aftermarket boost controller that may be why.

boost leak or wastegate stuck open?

get your head under the bonnet and check all inlet hoses for splits in hoses etc

have you done any thing to it lately, happened suddenly, getting worse?

Daniel will have a good look tomorrow problem being can,t see damn all around the v donks. Car seemed ok this morning it was when I was going to give a mitsoshitty lancer a seeing to that I realised lack of go, so yes happen suddenly.

Dont know if this is relevant, but my c34 does that on occasion, boost it normally runs is 11psi but sometimes it wont go past 7, turn it off wait a few minutes and its back to normal, I believe in an older thread you guys said this was something to do with the fact that stags run 7psi out of the factory and a computer hicup can cause it to limit itself to factory boost temporarily or something along those lines? So if your running an aftermarket boost controller that may be why.

Chris car runs factory boost so I,ll try again in the morning to see if it was a computer glitch if not back to head scratching or trip to Gold Coast to see specialist.

Gerry, have you ran a check for error codes yet?

The system may know what is wrong and give you an indication of where to look.

Worth a check before you take it to a specialist, could be something easily repairable by yourself or a small time mechanic.

Good luck.

Thanks everybody for your suggestions to my loss of performance but checked everything this morning and all looked ok so took it for a test run and it seems fine so we,ll see, shame really as it would have been a good excuse to get some more horsepower.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...