Jump to content
SAU Community

Recommended Posts

hey guys, what oil should i put in my diff? its in an R33gtst, should i use the 80-90 or the thicker 80/90-140? (not sure if its 80-140 or 90-140) also, should i use normal diff oil as apposed to LSD oil? as i beleive the diffs are VLSD and dont necessarily needs LSD oil

any help is apreaciated

cheers

Link to comment
https://www.sau.com.au/forums/topic/328173-80-90-or-8090-140-lsd-or-non-lsd/
Share on other sites

80-140 i would use on a track car, 80-90 for a street/track car. Nissan specifies 80-90 for japanese conditions iirc for rear LSDs

whats iirc? and is that an lsd fluid or normal?

mines a VLSD, would it need special lsd oil or standard gear oil?

Flushed and filled the LSD on both my 33's a couple of days ago with Castrol SAF-XA 80w-140 Full Synthetic Limited Slip Rear Axle Oil. No complaints so far and was told it’s a good oil. I’ve heard that if you have the limited slip diff, you must put LSD oil in or it will not work correctly but you can put LSD oil in non LSDs.

Run everyday 80w90 in your standard R33 GTS-T diff, mineral or synthetic. This will be fine unless it sees alot of track work - in which case you might want an 85w140 or similar. Note that you do not need to use a limited slip oil in a viscous LSD as a viscous LSD uses its own unservicable fluid inside the diff centre to operate. However, using limited slip oil will not do it any harm (aside from most mineral limited slip oils being a monograde 90 - non existent viscosity range).

Only mechanical diffs requires limited slip oil with anti-chatter additives.

Run everyday 80w90 in your standard R33 GTS-T diff, mineral or synthetic. This will be fine unless it sees alot of track work - in which case you might want an 85w140 or similar. Note that you do not need to use a limited slip oil in a viscous LSD as a viscous LSD uses its own unservicable fluid inside the diff centre to operate. However, using limited slip oil will not do it any harm (aside from most mineral limited slip oils being a monograde 90 - non existent viscosity range).

Only mechanical diffs requires limited slip oil with anti-chatter additives.

well i have put an anti chatter aditive in and its still grinding or "chatting" when turning, i cant for the life of me figure out whats wrong with it!

Did you read what I wrote mate? lol :(

You have a viscous diff, it does not need anti chatter additive...hence when you put it in it did nothing :D

Could be a manner of things wrong with it...these are use once and throw away diffs. Buy another one off eBay or put in a proper LSD.

lol do not trust many second hand items on eBay unless it's a solid state business with some impeccable feedback. Great nick is also a subjective use term haha. The plus to it is, if you choose to go with a decent LSD...you can get the centre installed in your spare diff housing while your car is still on the road...that's if you kept the old diff :D

Try Castrol SAF-XA out, if the LSD starts to behave strangly and locks up around a roundabout or in carparks (I heard it happening with Redline Shockproof in the diff, not sure if it was the grade 90w-140 or the fluid itself), just dump the fluid and go a different one.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...