Jump to content
SAU Community

Recommended Posts

Little harsh up top there. All been in good faith mate.

I'm becoming a little skeptical of my mates mechanical ability. I have put my trust in someone that has completed their apprenticeship + TAFE to know what they're on about, but having realised that I can install the pod filter myself.. im a bit suss of him.

The forums have been great, and a good way to source advice, parts & knowledge :D

Anyway, not important. What I'm looking for is a way to unbolt the AFM, seeing as the bottom bolts are impossible to reach :D

Already got my clamps, pod cleaned/oiled up & adaptor all ready to go, just got to get the bloody thing off

If I'm bored this arvo I might take my shit apart and post back with results.

oookayy... I can't edit my post.

That golden ring is bending like a mother f**ker... really, only thing I can think of is unbolting it regardless of the damage to it, and picking up another one from somewhere.

Edited by SKITTLES

WHAT A f**k AROUND.

Just been outside for the last 2 hours w/the old man attempting to fit it.

Main areas of concern being the filter being ridiculously hard to fit to the adaptor, its on to a point where it's not going to fall off but if I clamped it i'd be clamping onto nothing

The pods got nothing to stand on, its just chilling resting on top of the pipe underneath.

And the presence of a gap between the adaptor gasket and the adaptor, along each long side. Im worried that this will suck air in, there's no way for me to tighten it.

The golden ring thing is still attached, not sure if it's meant to stay on or not.

Love anyone who knows what they're doing to help me out :P

ok... i think you didnt need to oil that filter. im pretty sure its a dry filter...

the filter. goes on to the adaptor... the adaptor bolts on to the afm... you have to make sure you have the right adaptor.

which means take your afm. go to autobarn or super cheap. get them to give you an adaptor to match.

even if the holes on the adaptor are too far apart. you can always drill new ones.

there should be a rubber o-ring on the face of the afm (if im correct) this should seal the air.

of the bottom bolts of the afm are hard to reach. take out the rubber pipe that the afm is connected to. the one that goes to the turbo... i know that seems like "wtf" but sometimes you hafta do it. just for unbolting the afm.

once you have the adaptor on the afm... bolt it on to the rubber intake pipe whilst its all out of the engine... then install the ruber intake pipe over the turbo...

and then lastly force in the pod filter.

as for the pod sitting on nothing. thats fine. if you want to brace it down.. connect 2 zipties together and ziptie it to the pipe underneath. (your going to use alot of zipties with this car, liek alot of ppl do) BUT its temporary... get a bracket made up. heck get some spare sheet metal n bend it up yourself... its easy just bolt it to the back of one of the bolts thats on the afm. and then to an existing hole on the car..

i hope i didnt confuse you.

post up some pics. if your unsure. pics always help

Thanks for the posts, been very helpful :nyaanyaa:

All i'm concerned about now is that the pod filter (it does need to be oiled, came with a cleaning&oiling kit) seems to have an incredibly tight fit with the adaptor, as in it seems too "tight" and too "shallow" to fit on properly.

Also the gap in the rubber gasket concerns me, surely that isnt meant to be there

Will pull it apart this arvo and let ya know :)

Thunderbirds are go. Got it all in&running, everything is sweet.

Cheers for all the help guys, really appreciate it. These forums are a great source of info :(

Loving the sound of the pod on boost ;)

  • 1 month later...
Hey dude i would double check the rules for having a turbo car as i just got off my red p's today and was not allowed to drive a turbo. Also live in Perth

Huh? :ermm:

From the WA DPI site, there is no mention of Car restriction for P platers in WA, only the time restriction for Red Ps & the no alcohol limit.

Once you are grated a provisional license you will be on P plates for two years and the following rules and conditions apply:

  • You must display your P plates at all times when driving
  • You must have a zero blood alcohol level at all times when driving
  • Committing certain driving offenses as a P-plater could mean you automatically lose your license
  • You cannot drive between 12am-5am for the first 6 months after you have first become a P plater. For this period you will need to display red P plates. After the first six (6) months, you will be able to drive at any time of day and you will need to display green P plates. There are certain exemptions concerning these conditions. Please see the Rules for novice drivers (includes L and P platers) web page for more information.

I saw an L plater driving a Merc C63 AMG once...

Edited by Mayuri Krab
  • Like 1

I'm pretty sure in Victoria the restriction is only on P Platers, not L Platers.

So if your dad has a VE SS, you can learn to drive on it, but once you get your licence it's a big no no.

Makes sense if you ask me. I can't see many L Platers going spastic in a high powered car with mummy or daddy in the passenger seat. At least not if they had my parents lol.

  • Like 1

I got my R33 for $4500... 100,000km's on the clock. Mint condition with a kit :P I Guess I scored lucky. No paint or mechinical problems. Immaculate inside and out.

Must say, it's a good feeling to see someone with another stroke of luck

  • 5 months later...

sooo...is turbocharged cars restricted in WA for provisional drivers? I searched the forum and haven't got a clear answer. Am really close in getting an r33 as a first car.

No, go to the WA dpi site & it will say what I stated b4.

No restrictions on any cars (you can drive a Lambo, AMG, M5 if you have rich parents...), the current restriction for P platers are: 0 alcohol limit, night driving ban (from midnight till 5am for red Ps) & the newly introduced low demerit point system (4 point for Ps & 8 for Greens).

WA is one of the few states in Australia that doesn't yet have a car restriction list for P-platers, all the Eastern staes have them.

EDIT: DPI site: http://www.transport.wa.gov.au/licensing/20626.asp

Edited by Mayuri Krab

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...