Jump to content
SAU Community

Recommended Posts

hey all, ive owned this car for about 3 weeks, and it has a set of volk racing wheels, unsure on the exact brand, anyway, i cant get a socket or wheel brace to the nuts, the wheel nut holes are to small, where can i get a small socket to fit the nuts?

ta

Link to comment
https://www.sau.com.au/forums/topic/328853-cant-get-socket-on-wheel-nuts/
Share on other sites

maybe buy some internal hex wheel nuts?

thats what i had to do with my '32. the nuts are M12x1.25.

i paid $40 for 20 of them and they came with a hex bit as well.

other than that Stahlwille make some very thin walled sockets but they are massivley expensive. try about $750 for a basic socket set.

you may need to get a good quality socket as the cheaper ones are too thick to go in. then as said above, get some of the allen key head nuts.

or you can do what old mate in the honda did and take to the wheels with a saw............ LOL

as for getting the old ones out, best bet would be to drive to a hardware shop, or a decent tool shop and explain to them your problem and see if they will let you try some sockets to see if they fit. generally your better sockets such as stanely, kingchrome, snap-on etc will make skinnier sockets because they are made from stronger steel so don't need to be super thick to make up for being weak.

some tool shops have those annodised slimline sets in 4 colours that have the plastic covers on them to stop the socket from damaging the wheels. these are normally long and skinny for this purpose.

z-690500.jpg

  • 2 weeks later...

DO NOT USE INTERNAL HEX WHEEL NUTS!!! Had these on a rally car I bought and after heating cooling and a few wheel changes (fair enough rally car gets wheels on and off a lot more than a road car..) the pressure out on the inside of the nuts cracks them. If you simply think about the pressure is being applied as you tighten and loosen you will soon see how easy this can happen.... It may be poor quality, it may be a lot of work and all the hot cold, but I will still never use them again

you more than likely have 13/16th or 21mm nut's, best bet is uselly to use a spark plug socket, these are thin in the wall

and will get you out of trouble.

Nissan use 21mm wheel nut's, head down to your local tyre shop and buy some 19mm nut's and you should be right

and i aggree DO NOT use those stupid inner hex nut's, the amount of these that i've had to remove is huge..

you have to drill the head of the stud, and it's a massive pain in the arse, and we charge $65 per nut removelly

The Enkei rims I got came with a thinner extension as most sockets cannot get to the nuts due to the wheel design.

I'm sure you can buy them somewhere, or you can take any of the above tips.

LMAO!!! that link is hilarious. i like how the honda boys are blaming it on VW........who cuts a wheel. honestly. and then tries to justify doing it? hilarious read. my life if now better having seen that.

sry was off topic (sorta), all ideas above are good :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I came here to note that is a zener diode too base on the info there. Based on that, I'd also be suspicious that replacing it, and it's likely to do the same. A lot of use cases will see it used as either voltage protection, or to create a cheap but relatively stable fixed voltage supply. That would mean it has seen more voltage than it should, and has gone into voltage melt down. If there is something else in the circuit dumping out higher than it should voltages, that needs to be found too. It's quite likely they're trying to use the Zener to limit the voltage that is hitting through to the transistor beside it, so what ever goes to the zener is likely a signal, and they're using the transistor in that circuit to amplify it. Especially as it seems they've also got a capacitor across the zener. Looks like there is meant to be something "noisy" to that zener, and what ever it was, had a melt down. Looking at that picture, it also looks like there's some solder joints that really need redoing, and it might be worth having the whole board properly inspected.  Unfortunately, without being able to stick a multimeter on it, and start tracing it all out, I'm pretty much at a loss now to help. I don't even believe I have a climate control board from an R33 around here to pull apart and see if any of the circuit appears similar to give some ideas.
    • Nah - but you won't find anything on dismantling the seats in any such thing anyway.
    • Could be. Could also be that they sit around broken more. To be fair, you almost never see one driving around. I see more R chassis GTRs than the Renault ones.
    • Yeah. Nah. This is why I said My bold for my double emphasis. We're not talking about cars tuned to the edge of det here. We're talking about normal cars. Flame propagation speed and the amount of energy required to ignite the fuel are not significant factors when running at 1500-4000 rpm, and medium to light loads, like nearly every car on the road (except twin cab utes which are driven at 6k and 100% load all the time). There is no shortage of ignition energy available in any petrol engine. If there was, we'd all be in deep shit. The calorific value, on a volume basis, is significantly different, between 98 and 91, and that turns up immediately in consumption numbers. You can see the signal easily if you control for the other variables well enough, and/or collect enough stats. As to not seeing any benefit - we had a couple of EF and EL Falcons in the company fleet back in the late 90s and early 2000s. The EEC IV ECU in those things was particularly good at adding in timing as soon as knock headroom improved, which typically came from putting in some 95 or 98. The responsiveness and power improved noticeably, and the fuel consumption dropped considerably, just from going to 95. Less delta from there to 98 - almost not noticeable, compared to the big differences seen between 91 and 95. Way back in the day, when supermarkets first started selling fuel from their own stations, I did thousands of km in FNQ in a small Toyota. I can't remember if it was a Starlet or an early Yaris. Anyway - the supermarket servos were bringing in cheap fuel from Indonesia, and the other servos were still using locally refined gear. The fuel consumption was typically at least 5%, often as much as 8% worse on the Indo shit, presumably because they had a lot more oxygenated component in the brew, and were probably barely meeting the octane spec. Around the same time or maybe a bit later (like 25 years ago), I could tell the difference between Shell 98 and BP 98, and typically preferred to only use Shell then because the Skyline ran so much better on it. Years later I found the realtionship between them had swapped, as a consequence of yet more refinery closures. So I've only used BP 98 since. Although, I must say that I could not fault the odd tank of United 98 that I've run. It's probably the same stuff. It is also very important to remember that these findings are often dependent on region. With most of the refineries in Oz now dead, there's less variability in local stuff, and he majority of our fuels are not even refined here any more anyway. It probably depends more on which SE Asian refinery is currently cheapest to operate.
    • You don't have an R34 service manual for the body do you? Have found plenty for the engine and drivetrain but nothing else
×
×
  • Create New...