Jump to content
SAU Community

Recommended Posts

  • Replies 107
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 weeks later...

Spent a silly amount of money getting all 7 seats and the headlining steam-cleaned, but it was definitely worth it. Interior came up much better with a professional detail. Also, some more quick photos. Needs photoshop coilovers hehe

PB060611.jpg

PB060612.jpg

PB060609.jpg

PB060604.jpg

I'm still loving the fuel economy.

  • 2 weeks later...

No mods to report. New centre console lid latch arrived, so I put that on today. Unfortunately didn't match my trim colour but it's not like you see it with the lid closed anyway. So now I have a functioning centre console.

latch1.jpg

latch2.jpg

latch4.jpg

latch3.jpg

And chucked on my JDMST sticker. The Skyline feeling lonely in the reflection. I drove the Skyline for the first time since I got the Cube today. Feels like I'm sitting on the ground compared to the Cube. Gone are the awesome viewing angles, comfy suspension and light steering.

sticker1.jpg

sticker2.jpg

  • 4 weeks later...

The Cube's come with a massive, obnoxious aerial which makes it impossible to go under tree's, into carparks, etc. I installed a much smaller aerial today. It was listed as being for a 350Z but came with universal adapters. It also hasn't affected reception at all.

Before:

PC290607.jpg

PC290609.jpg

PC290611.jpg

PC290614.jpg

After:

PC290620.jpg

PC290618.jpg

PC290615.jpg

  • 3 weeks later...

Ordered:

*Genuine Neoclassical Kit

*Genuine CUBE3 Side Stickers

*Genuine Bonnet Sticker

*Genuine Cargo Net

It was always my intention to have the neoclassical overfender & sticker kit on the car, I just had to wait until I had enough money because it's not cheap buying brand new genuine Nissan. But god it'll look great once it's on. At the same time I'll get the little ding that came with the car on the rear bumper fixed and resprayed. Happy :D

  • 4 weeks later...

My kit and stickers arrived last week but I have a mental dilemma. I'll be respraying the rear bumper to get rid of a dent that it came with from Japan, and at the same time this will take care of the colour-matching issue the bumper currently has (that is a normal thing being that the paint on the plastic ages differently to the paint on the metal over time and pearl white is the worst colour for showing this.) Now obviously the paint on the front bumper has done exactly the same thing. I'm thinking if I go to all the trouble of doing the rear and then not doing the front I'll keep looking at it, knowing it doesn't match and regretting it. Arggggh, I hate feeling the need to repair something that isn't broken.

Looks like I'll save up to get both bumpers resprayed and the kit and stickers fitted professionally. I know the kit and stickers are something that I could do myself, but I'm always scared of screwing up things on the body. Maybe best to leave it to a professional?

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...