Jump to content
SAU Community

Recommended Posts

hey all im having some issues with my gtr r32 i get the 4wd light come on if i start the car and let it warm up but if i start the car and drive straight away it all works

any ideas?

Check the ATTESSA computer in the boot for error codes (do a search here or refer to the manual for how to do this).

My bet is error code 18

  • 1 year later...

Check the ATTESSA computer in the boot for error codes (do a search here or refer to the manual for how to do this).

My bet is error code 18

Long time later to revive the thread but what is the fix for error code 18?

I changed the Attessa pressure switch (pain in the backside job) and still had the light come on and no 4wd?

Cheers

  • 1 year later...

Anymore info on this?

ive had a few issues the last couple of days and im getting error code 18

18 – ETS pressure switch or circuit

is it generally the switch that is faulty or can it be dodgy wiring, im guessing it could be either or...

its a bit of an intemidant fault atm, generally when i start it up cold its good to go, but if i stop then try to start it up again it generally comes on

from quick research the switch is above the final drive

this has only started to happen since a removed the engine and did a few mods while it was out.. i also pulled out all the solenoids in the Hicas system though surely that isnt the problem

i havent disconnected any off the ATTESSA LINES so im assuming its all bled and ready to go, I "assume" but i will do a bleed anyway.. just looking for peoples experiences with this

After some more research ive found the its usually the pressure switch thats at fault and generally the pump needs to be replaced :/

Its a pretty big job from what ive been reading from, i just find it very odd that its all of a sudden happened now after i done all these mods

Righto so after closer inspection there seems to be some oil leaking on the rear diff.. it doesnt actually look like its coming from the rear diff as there oil all over the top bushes... im guessing there is a small leak in the pressure switch or there abouts

really need to get the car up in the air for a proper inspection..

the fluid level has also dropped in the reservoir so thats really a dead give away that theres a leak somewhere...

will report back on closer inspection

Ok so there was the tiniest leak coming from the nipple below the pump so I have it a tighten..

Also noticed a large build up of gunk on the rear right hand abs/wheels speed sensor on the drive shaft.. Gave it a good clean and now the trouble has seemed to did appear..

What that has to do with error 18 "ETS pressure switch or circuit" I have no idea

Will give it another couple of days before I claim victory

Haven't bled it yet

It might have been causing the ATTESSA system to do something in response to the strange wheel speed signal (don't even know if this can occur) and the consequent unusual operating condition of the ATTESSA system caused high or low or whatever wrong pressure - enough to cause code 18.

/wild theory.

Hmmm our theories just went out the window :(

It seems to be that initial priming of the ATTESSA is determining weather or not the 4wd is going to work or not

If I start the car up and and it doesn't and the 4wd light doesn't come on within the first 5 seconds it won't come on at all..

The fault is very tempremental so I'm considering looking for another switch as it seems the most Likely cause atm... This would appear obviouse considering the fault code but I've read many threads where people have replace the switch with a known working one and still had the fault lol

Ok found a workshop manual,

As per the fault diagnostic ice checked PIN number 42 for ground at the back of the ATTESSA ECU

There was ground there so tomorrow I will need to get under the car to check PIN number 3 and 4 for earth at the ETS hydraulic unit plug

Have it a mega good bleed today.. Issue is still there.. Also checked the 4 pin plug that goes to the switch.. Looks pretty clean

Check the earths at pin 42 and 4 as designated by the workshop manual fault chart..

Everything so far as been pointing towards "ETS hydraulic unit is faulty"

Looks like it pretty much a diff out job atm

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • HFM BM57 has a "bad" knee point, IIRC. It's not the same thing as the later R chassis MC.
    • The ATTESSA is functionally identical to R34; there were a bunch of JDM models that continued ATTESSA including Fuga/Q70, Skyline/Q50, Cima etc as an option. All with Auto only and I think mostly for snow regions. AFAIK there were no AWD VR30DDTT sold in Australia - it is on my to do list to check regs for racing a LHD car in Targa/ATR/AASA/CAMS events because if I can get the auto to work it would be interesting to run a 4wd car The Ecuteck TCM tuning is the same model as their ECU tuning, they already have it for R35 and Dose's favourite, BMW. You buy "points" to allow your computer to be tuned, buy either a bluetooth (phone app) or bluetooth+USB+Key (phone and PC) dongle, and pay for a tune that will be locked to your tuner ( ). You can also access the tuning software yourself but 1. it is mega expensive and 2. these computers have a billion parameters that intersect, so how could you ever spend enough time on it to get a decent result.
    • Or, is it a case of what it is like owning an R series Skyline? NFI what the previous owner has done or fiddled with... Ha ha ha After reading through this thread, I went on a bit of a research about the Q50/Q60. Now I'm quite intrigued by them! Is the AWD in them more like a WRX where it's always AWD, or is it more like the ATTESSA in the GTRs? By the sound of this TCU tuning, this sounds like a case of someone has made some real software for it, and you just need the right piece of hardware, and then you license that specific vehicle/TCU. Or is this a case of the software will be really expensive so only a few tuners have it, and you still have to pay a license per vehicle?
    • By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
×
×
  • Create New...