Jump to content
SAU Community

Recommended Posts

hey all im having some issues with my gtr r32 i get the 4wd light come on if i start the car and let it warm up but if i start the car and drive straight away it all works

any ideas?

Check the ATTESSA computer in the boot for error codes (do a search here or refer to the manual for how to do this).

My bet is error code 18

  • 1 year later...

Check the ATTESSA computer in the boot for error codes (do a search here or refer to the manual for how to do this).

My bet is error code 18

Long time later to revive the thread but what is the fix for error code 18?

I changed the Attessa pressure switch (pain in the backside job) and still had the light come on and no 4wd?

Cheers

  • 1 year later...

Anymore info on this?

ive had a few issues the last couple of days and im getting error code 18

18 – ETS pressure switch or circuit

is it generally the switch that is faulty or can it be dodgy wiring, im guessing it could be either or...

its a bit of an intemidant fault atm, generally when i start it up cold its good to go, but if i stop then try to start it up again it generally comes on

from quick research the switch is above the final drive

this has only started to happen since a removed the engine and did a few mods while it was out.. i also pulled out all the solenoids in the Hicas system though surely that isnt the problem

i havent disconnected any off the ATTESSA LINES so im assuming its all bled and ready to go, I "assume" but i will do a bleed anyway.. just looking for peoples experiences with this

After some more research ive found the its usually the pressure switch thats at fault and generally the pump needs to be replaced :/

Its a pretty big job from what ive been reading from, i just find it very odd that its all of a sudden happened now after i done all these mods

Righto so after closer inspection there seems to be some oil leaking on the rear diff.. it doesnt actually look like its coming from the rear diff as there oil all over the top bushes... im guessing there is a small leak in the pressure switch or there abouts

really need to get the car up in the air for a proper inspection..

the fluid level has also dropped in the reservoir so thats really a dead give away that theres a leak somewhere...

will report back on closer inspection

Ok so there was the tiniest leak coming from the nipple below the pump so I have it a tighten..

Also noticed a large build up of gunk on the rear right hand abs/wheels speed sensor on the drive shaft.. Gave it a good clean and now the trouble has seemed to did appear..

What that has to do with error 18 "ETS pressure switch or circuit" I have no idea

Will give it another couple of days before I claim victory

Haven't bled it yet

It might have been causing the ATTESSA system to do something in response to the strange wheel speed signal (don't even know if this can occur) and the consequent unusual operating condition of the ATTESSA system caused high or low or whatever wrong pressure - enough to cause code 18.

/wild theory.

Hmmm our theories just went out the window :(

It seems to be that initial priming of the ATTESSA is determining weather or not the 4wd is going to work or not

If I start the car up and and it doesn't and the 4wd light doesn't come on within the first 5 seconds it won't come on at all..

The fault is very tempremental so I'm considering looking for another switch as it seems the most Likely cause atm... This would appear obviouse considering the fault code but I've read many threads where people have replace the switch with a known working one and still had the fault lol

Ok found a workshop manual,

As per the fault diagnostic ice checked PIN number 42 for ground at the back of the ATTESSA ECU

There was ground there so tomorrow I will need to get under the car to check PIN number 3 and 4 for earth at the ETS hydraulic unit plug

Have it a mega good bleed today.. Issue is still there.. Also checked the 4 pin plug that goes to the switch.. Looks pretty clean

Check the earths at pin 42 and 4 as designated by the workshop manual fault chart..

Everything so far as been pointing towards "ETS hydraulic unit is faulty"

Looks like it pretty much a diff out job atm

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...