Jump to content
SAU Community

Looking For Lower Seat Than Gt-r Seat

On Edge

By On Edge,
in Motorsport Discussion & Builds

 Share

Recommended Posts

On Edge Veteran

On Edge

Posted
Posted

hey people,

i currently have nismo 400r seats in my r33 an would like to buy a fixed bucket seat for holding, as well as having a lower seating position.

my question is do most fixed back seats sit lower than the GT-R one? An if so by how much

Any help would be much appreciated

phunky_monkey Grand Master

phunky_monkey

Posted
Posted

The lower seating position is usually achieved by the rail rather than the actual seat itself. If you want to go low and don't want to go custom, I'd suggest a Bride Super Low rail teamed up with whichever seat you like (and that fits).

On Edge Veteran

On Edge

Posted
  • Author
Posted
The lower seating position is usually achieved by the rail rather than the actual seat itself. If you want to go low and don't want to go custom, I'd suggest a Bride Super Low rail teamed up with whichever seat you like (and that fits).

thanks for the reply

yes low rails will definately help, an i think that the GT-R seat is a lil chunky underneath.

Im looking at getting the sparco evo 2 plus with low rail, hope it sits lower

Can anyone confirm?

FineLine Grand Master

FineLine

Posted
Posted
thanks for the reply

yes low rails will definately help, an i think that the GT-R seat is a lil chunky underneath.

Im looking at getting the sparco evo 2 plus with low rail, hope it sits lower

Can anyone confirm?

Thats the exact combo i am using and yes it is lower than the 33 gtr seat. I have the gtr seat as a passenger seat and there is a noticeable difference in seat height.

  • Nope 1
phunky_monkey Grand Master

phunky_monkey

Posted
Posted
thanks for the reply

yes low rails will definately help, an i think that the GT-R seat is a lil chunky underneath.

Im looking at getting the sparco evo 2 plus with low rail, hope it sits lower

Can anyone confirm?

What rail is it?

Yes the seat is chunky, but I'm telling you that 90% of the height difference will be in the choice of rail.

Beer Baron Grand Master

Beer Baron

Posted
Posted

yep, rail design is the key. sometimes you will need a base plate to provide a flat surface, then bolt sliders to that so seat can move back and forward and then you bolt your side mounts to the sliders and the seat to the mounts. with all that stuff you end up with a fair bit of height. removing the sliders gives back about 20mm or so maybe even 30mm depending on design. you do still need some kind of base plate though to give a level mounting surface for the side mounts. the other option is modify the floor to allow you get a flat frame for the seat nice and low. lot of work though and must be done professionally.

phunky_monkey Grand Master

phunky_monkey

Posted
Posted
the other option is modify the floor to allow you get a flat frame for the seat nice and low. lot of work though and must be done professionally.

I had this done in the 180, and although it was pricey my shoulder now lines up with the door frame and I'm 6'4. Super low!

Having said that, a good Bride super low rail will drop you significantly for around $300. The drop depends on the car; in the 180 it was great until I got the cage which obstructed my seating position. In the STi I sit even lower than the 180 with the modified floor (feels that way anyway). Ridiculously low at it's lowest setting, but three heights to choose from.

Buddhz Apprentice

Buddhz

Posted
Posted

So which bride rail did you have before you modified your floorpan Dane?

Was it low enough for you to wear a helmet without the cage?

I have a bride rail with an older model Profi SPG in my S13 atm (its not the lowest one) and with a helmet my head hits the roof. I'm only 6' as well which is strange - maybe my body is out of proportion :(

phunky_monkey Grand Master

phunky_monkey

Posted
Posted

It may be mate! :(

I think it was an FO, and I fit with just enough room though I'm 4 inches taller than you. That's with an SPA so much of a muchness.

In the STi I have an FG and it is super low, so I'd actually suggest trying one of those out.

FineLine Grand Master

FineLine

Posted
Posted
So which bride rail did you have before you modified your floorpan Dane?

Was it low enough for you to wear a helmet without the cage?

I have a bride rail with an older model Profi SPG in my S13 atm (its not the lowest one) and with a helmet my head hits the roof. I'm only 6' as well which is strange - maybe my body is out of proportion :(

mate just go to revolution race gear and get the generic seat rail they sell for the sparco evo 2. I'm 6'1 and I have no damn probs with a helmet and a roll cage.

  • Nope 1
On Edge Veteran

On Edge

Posted
  • Author
Posted
mate just go to revolution race gear and get the generic seat rail they sell for the sparco evo 2. I'm 6'1 and I have no damn probs with a helmet and a roll cage.

thats where im buying my seat an the rail im looking at using, did you have much trouble with installation?

FineLine Grand Master

FineLine

Posted
Posted
thats where im buying my seat an the rail im looking at using, did you have much trouble with installation?

None at all, when I got around to doing the cage I had to cut the rail that seperates both side rails so the seat could go down a slot or 2. Its pretty basic stuff mate.

  • Nope 1
phunky_monkey Grand Master

phunky_monkey

Posted
Posted
mate just go to revolution race gear and get the generic seat rail they sell for the sparco evo 2. I'm 6'1 and I have no damn probs with a helmet and a roll cage.

I have a generic type base rail with RPM side mounts in my passeneger seat, check the height difference out. That's without sliders too.

BUT I didn't cut the middle out to drop it, don;t think I can with the width of the SPG-N.

post-8405-1281065615_thumb.jpg

FineLine Grand Master

FineLine

Posted
Posted
omg thats great :( sorry to be a pain but how much do you reckon the driving height would have been lowered from a GT-R seat?

wish my car was here and not at the workshop so i could actually go measure.

From memory about 25/30 mil. You can also rake the seat back a bit to give yourself more head room by going to a lower slot on the back.

  • Nope 1
FineLine Grand Master

FineLine

Posted
Posted
I have a generic type base rail with RPM side mounts in my passeneger seat, check the height difference out. That's without sliders too.

BUT I didn't cut the middle out to drop it, don;t think I can with the width of the SPG-N.

I see what you mean phunk. That rail is a different animal to mine. Mine is actually a slider and is way lower than that puppy.

  • Nope 1
On Edge Veteran

On Edge

Posted
  • Author
Posted
wish my car was here and not at the workshop so i could actually go measure.

From memory about 25/30 mil. You can also rake the seat back a bit to give yourself more head room by going to a lower slot on the back.

yeah tru that, beautiful cant wait to get it, do you remember what the name of the rail was?

FineLine Grand Master

FineLine

Posted
Posted

Now that I cant help you with. what I can tell you to assist with I.d. is that it has a lever on either side of the rail with a brass knob on the end. these levers are lifted to the verticval position to slide the rail and back to the horizontal to lock it in place.

  • Nope 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      R34 GT-T cycling ABS pump

      By Kinkstaah · Posted

      Lets say I wanted to buy this, specifically for this purpose. How do I actually perform the function. Can I still buy a Consult-1? Am I about to be burned by the fact my car is a 2000 model Series 2 R34 and thus will be some stupid other system? Do I just need this -> https://obd2australia.com.au/product/nissan-consult-14-pin-to-usb-ddl-diagnostic-interface-with-ftdi-ft232r-chip/ And with what software?
    • GTSBoy
      33 GTR Broken front wheel knuckle

      By GTSBoy · Posted

      That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • R32 TT
      33 GTR Broken front wheel knuckle

      By R32 TT · Posted

      Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • MBS206
      33 GTR Broken front wheel knuckle

      By MBS206 · Posted

      Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • GTSBoy
      R34 auto to manual conversion help

      By GTSBoy · Posted

      The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
×
×
  • Create New...