Jump to content
SAU Community

Recommended Posts

What is this PCV valve is it present on standard RB's and Neo's or what?

PCV valve is positive crankcase ventilation valve. most cars have them - they basically release any buildup of combustion gasses that sneak past the piston rings and in under the cam covers. this is also called 'blowby'.

the PCV is the factory way of releasing that pressure. the valve opens when the crankcase is under positive pressure, releasing the gasses and any oil vapour back into the intake where it cycles back into the engine and is burnt off in the next combustion cycle.

a way that tuner's approach this is to get rid of this system and run a breathable catch can - which vents that vapour to the atmoshpere naturally, and then using a series of baffles, attempts to get the oil particles out of the vapour, where the accumulate in the bottom of the catchcan to be drained later. because it is unmetered exhaust releasing to atmosphere, they're illegal.

after that explanation, i'd be curious to see how he thinks the PCV is contributing to the miss. unless it is sticking shut, and then snapping open and releasing a big pressurised hit back into the intake - but that could only upset the AFR if it was entering the intake before the AFM?? either way, it's easy to eliminate the possibility just remove the return pipe from the intake and plug the intake hole with your thumb. if its still doing it, it's not your problem!

EDIT: just thinking this over in the back of my head, it could be stuck - yes. but it could be stuck OPEN, which would cause a vaccum leak and create a lean misfire. to check this, take the hose off at the PCV valve, and block the PCV valve with your thumb. all in all, pretty quick checks!

and if you just want to service it for peace of mind, grab some throttle body cleaner (carby cleaner) and remove the PCV. soak it in a cap full of the stuff. shake it round a bit and it should start moving freely again. do your throttle body while you're at it.

Edited by SLYLINER

EDIT: just thinking this over in the back of my head, it could be stuck - yes. but it could be stuck OPEN, which would cause a vaccum leak and create a lean misfire. to check this, take the hose off at the PCV valve, and block the PCV valve with your thumb. all in all, pretty quick checks!

and if you just want to service it for peace of mind, grab some throttle body cleaner (carby cleaner) and remove the PCV. soak it in a cap full of the stuff. shake it round a bit and it should start moving freely again. do your throttle body while you're at it.

thats basically what the mechanic has said but he told me to just buy a new 1 cause it should be pretty cheap and throttle body and injectors have already been cleaned

Just tried cleaning mine and still no joy.

Going to go get a new set of plugs (even though these only done 2,500) sometime soon

when i went to mechanic he cleaned mine aswell it was fine for a lil while then came back but he did say i need to replace it

  • 2 weeks later...

Turns out my issue was my timing on base idle was well out... I should have chucked the light on it ages ago but its been with a mate! Dialed it in on the dyno today and shes happy again :-)

  • 1 month later...

Replaced my plugs with coppers today, the miss on idle has gotten worse but it seems to be smoother on and off throttle especially noticable whilst going down hill. Am going to replace o2 sensor in a couple of weeks, i havent ever replaced it and its done 160,000km now.

This miss has got to be sorted out, its starting to shit me. The last time it was this bad was about two years ago and i tracked it down to the hose that crosses over the rocker covers at the front having a split in it. Maybe it is a hose.

When u sit there with your foot resting on the throttle giving it a flat constant rev at one rpm anywhere in the rev range its got a miss but you dont feel it when your driving.

Replaced my plugs with coppers today, the miss on idle has gotten worse but it seems to be smoother on and off throttle especially noticable whilst going down hill. Am going to replace o2 sensor in a couple of weeks, i havent ever replaced it and its done 160,000km now.

This miss has got to be sorted out, its starting to shit me. The last time it was this bad was about two years ago and i tracked it down to the hose that crosses over the rocker covers at the front having a split in it. Maybe it is a hose.

When u sit there with your foot resting on the throttle giving it a flat constant rev at one rpm anywhere in the rev range its got a miss but you dont feel it when your driving.

How do you reset the ecu?

  • 1 month later...

Yay, my cars miss is all sorted out. Took it to the mechanics about 2 weeks ago and they said the timing was out 4 degrees so they adjusted that and cleaned the air flow meter but the miss was still there, slightly better but still there.

They checked a few more things but couldnt figure out why it was there. They said the only thing they could think it would be is a dirty injector, so i pulled them out and had them tested and cleaned and re-tested.

The injectors came up 10% difference between the lowest and the highest pressure, the spray and spray angle was good. They got them within 2% from highest to lowest after cleaning them. There tolerance is 3%

My car has never sounded so smooth, no more popping. Its actually gotten quieter, Im wrapped

Yay, my cars miss is all sorted out. Took it to the mechanics about 2 weeks ago and they said the timing was out 4 degrees so they adjusted that and cleaned the air flow meter but the miss was still there, slightly better but still there.

They checked a few more things but couldnt figure out why it was there. They said the only thing they could think it would be is a dirty injector, so i pulled them out and had them tested and cleaned and re-tested.

The injectors came up 10% difference between the lowest and the highest pressure, the spray and spray angle was good. They got them within 2% from highest to lowest after cleaning them. There tolerance is 3%

My car has never sounded so smooth, no more popping. Its actually gotten quieter, Im wrapped

That's a great result, glad to hear. I actually developed a slightly rough idle after going to 600cc injectors (neo); this was apparently to do with not having quite enough resolution in the latency settings. It doesn't bother me; sounds kinda 'tough', and for the increase in power I'll tolerate it :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...