Jump to content
SAU Community

Recommended Posts

Hi people,

I have to admit i didn't use the SEARCH function on this question, a little lazy.

I am wondering if the petrol you pump into your vehicle will stay 'fresh' after 2 weeks inside your car?

I remember i read from somewhere on the forums where people did mention that the 98RON might lose a few 'RONs' or something like that.

Link to comment
https://www.sau.com.au/forums/topic/332629-petrol-quality/
Share on other sites

2 weeks LOL... nothing will happen.. Well nothing to be concerned about... My fuel opften takes 1 month or so to get used... Still drives fine.. I'd only be concerned if your running high end power.. My fuel was sitting there for just over 8 months.. and finally drove the car the other day.. Mind you i am staying off boost until a fresh tank can be run though..

Edited by .:: GimpS-R34 ::.
Link to comment
https://www.sau.com.au/forums/topic/332629-petrol-quality/#findComment-5394835
Share on other sites

fuel doesn't go stale in 2 weeks. it does go stale over time, but not in 2 weeks, or even a month really. that said a car will still run on fuel that is pretty old, just not that well. i've got an old commodore and the fuel in it is a mix of about 6 months old and 2 years old and it still starts and runs. my mother has a 2000 model corolla and she had to have an operation and couldn't drive for about 3 months and her car ran fine after those 3 months (i drove it occasionally during those 3 months, but never put fuel in it)

Link to comment
https://www.sau.com.au/forums/topic/332629-petrol-quality/#findComment-5395053
Share on other sites

the amount that it gets diluted it's not worth thinking about though.

but in case you wanted to think about it.....

fill 1: 50L of fuel put in. for arguments sake we'll say it's a 50L of fuel and was drained prior to filling

fill 2: filled up with 10L left, so there's 40L fresh fuel and 10L 1 week old fuel

fill 3: filled up with 10L left, so now there's 40L fresh, 2L from fill 1 and 8L from fill 2

fill 4: filled up with 10L left, so now there's 40L fresh, 400ml from fill 1, 1.6L from fill 2 and 8L from fill 3

fill 5: same as above but now the 10L consists of 80ml of fill 1, 320ml from fill 2, 1.6L of fill 3 and 8L of fill 4.

so when you look at it like that, 40L is from the current fill, 8L is only 1 fill old and the remaining 2L is 2 fills or older and the stale fuel from fill 1 is going to be negligable (only 400mls of fuel in the tank is from 3 or more fills ago). the amount of fuel that is multiple fills old is always going to be small even if you will up with more than 10L to go.

but theoretically speaking the fuel tank still contains an extremely tiny amount of fuel from the very first time it was filled up.

Link to comment
https://www.sau.com.au/forums/topic/332629-petrol-quality/#findComment-5397712
Share on other sites

I dont think fuel goes of that quickly, it would take a few months atleast. It might depend on weather to? I think in the summer it may go off quicker but still not in a time span you would have to worry about unless you wern't going to drive your car for like 6 months. Even then it should be fine.

I have driven cars straight of the boat from japan and they drive fine and god knows how old the fuel is by time the car reaches Aus.

Link to comment
https://www.sau.com.au/forums/topic/332629-petrol-quality/#findComment-5397769
Share on other sites

Fuel does go stale over time. But months or years, not weeks, something like methanol you'd need to be more careful about but not boring unleaded. Lol. Get cars at work driven in by the "seniors", they keep the tanks filled to the neck and re-filled weekly after their one trip to the shops, fuel comes out yellow and has no smell to it, car runs, but poorly, but this is after 5+ years. And usually it's the water in the fuel causing problems in these cases...

Also, my car was knocking under load (so I stopped loading it) on it's journey home post-purchase (import from a dealer), good tank of 98' and it went away...

Link to comment
https://www.sau.com.au/forums/topic/332629-petrol-quality/#findComment-5398797
Share on other sites

fuel doesn't go stale in 2 weeks. it does go stale over time, but not in 2 weeks, or even a month really. that said a car will still run on fuel that is pretty old, just not that well. i've got an old commodore and the fuel in it is a mix of about 6 months old and 2 years old and it still starts and runs. my mother has a 2000 model corolla and she had to have an operation and couldn't drive for about 3 months and her car ran fine after those 3 months (i drove it occasionally during those 3 months, but never put fuel in it)

Thanks for sharing.

__________________

Watch Piranha 3D Online Free

Edited by nicoledc109
Link to comment
https://www.sau.com.au/forums/topic/332629-petrol-quality/#findComment-5401775
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...