Jump to content
SAU Community

Holinger Sequential

T04GTR
 Share

Recommended Posts

T04GTR Grand Master

T04GTR

Posted
Posted

hi all, i was just wondering, is there a standard set of ratios for the 6 speed holinger sequential for the gtr?

what seems to be the commonly chosen ones? 6th being overdrive.

cheers

also, does anyone know what the mainshaft to countershaft distance is on the seq holinger?

ie. the os88 is 88mm....

Link to comment
https://www.sau.com.au/forums/topic/332939-holinger-sequential/
Share on other sites
fun123 Rookie

fun123

Posted
Posted
hi all, i was just wondering, is there a standard set of ratios for the 6 speed holinger sequential for the gtr?

what seems to be the commonly chosen ones? 6th being overdrive.

cheers

also, does anyone know what the mainshaft to countershaft distance is on the seq holinger?

ie. the os88 is 88mm....

There are no set ratios, leagh at Hollinger will send you a chart to choose from, Tomei has chisen two different otions.

Imput shaft can be standard 24 spline but most people choose the chevy 26 spline unit as this was a weak point of the original nissan gearbox.

Main shaft to counter shaft distance, call Hollinger.

If you buy one be prepared to put regular gearsets in it, they do wear out and are costly.

  • 9 months later...
Beer Baron Grand Master

Beer Baron

Posted
Posted

pretty sure the GTR hollingers are an HS6 so yeah with the right bellhousing and adapter for the transfer case it should be fine. as long as what you're buying from a V8 is an HS6 too. call hollinger and I'm sure they can tell you. but by the time you buy the right hollinger/RB bellhousing, and the transfer case fitting it might not be worth it. also need to take into account the ratios it comes with might not be suitable.

Beer Baron Grand Master

Beer Baron

Posted
Posted

actually looks like they are not an HS6 after all. and apparently V8SC don't use HS6 now either. it's still possible you could buy one and then buy the bellhousing for the front and the transfer case mount/adapter for the rear but again by the time you do all that just buy the right GTR box?

have a look at the holinger site. it's been updated recently I was told. if you look at the centre of the old GTR boxes (which is the gearbox with the front being just bellhousing and the rear is transfer adapter) it does look a bit like an HS6 but better to check before doing anything.

Beer Baron Grand Master

Beer Baron

Posted
Posted

don't worry I've had that same thought before too.

"hmm, plenty of 6spd sequential hollingers getting around in varous V8SC.... hmmm now how do I put that into my GTR???" lol.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Just_a_datsun
      RB26 block, rb26 head

      By Just_a_datsun · Posted

      Block bump. $400. As above cyl 6 needs bore or sleeve.
    • Kinkstaah
      Blue slip

      By Kinkstaah · Posted

      I would think making the argument that the travel is limited by a spring flexing against a spring perch as "the same method". Later on in the document they do state that the spring can't bind on full bump travel and cannot come loose in full rebound travel as well. (which is all very sensible). The laws are actually pretty sensible and reasonable. It's just that the people who enforce and check them don't actually read them or know them accurately. "Oh, coilovers? Instant fail mate. Don't even need to look at it." - Guy who will be instantly reported by me. There is probably merit to people who do get defected for height also get defected for the suspension in that state that allows it. I did never consider the people who are complaining about coilovers being picked on are also running around at 50mm off the floor.
    • Kinkstaah
      Ethanol Content Sensor - Always at 11%?

      By Kinkstaah · Posted

      I think given SAU's knowledge of E85 we can strongly conclude that 10% ethanol in almost any situation is entirely fine. Almost all of the myths against E85 were overblown, let alone E10.
    • The Bogan
      Blue slip

      By The Bogan · Posted

      From your link See bold text, is this referring to damper settings, if so that may a issue for "some" inspectors, I cannot see aftermarket coilovers having the evidence that "must be available that its functional performance is equivalent to the original" Maybe just remove the adjustment knows and hope for the best???? Meh 5.2 Suspension travel In all instances, modifications to a vehicle’s suspension must ensure the integrity of the system and not compromise the ride quality. At least two thirds of the original suspension travel should be maintained in both directions (rebound (i.e. extension) and bump (i.e. compression)), and rebound must be limited by the same method used by the vehicle manufacturer or if this is not practicable due to the nature of the modification, an equivalent method. If an alternative method is used, evidence must be available that its functional performance is equivalent to the original.
    • Kinkstaah
      Blue slip

      By Kinkstaah · Posted

      They actually don't - They adhere to VSB14 rules just like Victoria. The rules are against CABIN adjustable height, and it quite clearly states that the height has to be within parameters. I asked the VASS engineer to confirm this when I got my car engineered and they refused to engineer the coilovers because they didn't meet the requirements for requiring engineering. (mine are height adjustable.) People "Not wanting to bother" with "Actually reading/knowing/adhering to the rules" should result in fines and immediately losing the ability to issue blue slips and/or RWC's in Vic.
×
×
  • Create New...