Jump to content
SAU Community

Recommended Posts

i was just wondering how many of you have thrown a front mount on there r33 but still using the series 1 front bar.

not series 1.5 im looking for s1.

id love to see some pictures and details on how difficult it was with the stock bar.

thanks!

reference is my car,,, ugly s1 bumper :)

post-61916-1282210501_thumb.jpg

I like s1 bumper, its so..............plain....

Not too difficult,you will have to trim some of the bar, the side scoops mostly to clear pipes and a little out of the middle but not much..biggest problem i reckon is the aircon fan gets in the way so you need to cut the reobar...maybe a smaller fan or something could solve this, i just disposed of the aircon instead... :)

But yeah if you can be rid of that fan somehow its an easy fit...

But if your careful you can squeeze it in so neatly you can hardly notice it

if you want it noticed however,best to get another bar...

you might have to angle the intercooler a bit to miss some stuff

Mine had to be angled a bit to clear the driving light/indicator assembly and the A/C fan.

best thing to do is just to take the front bar off, mount the intercooler then trial fit the front bar till you get the intercooler at the right angle and trim the front bar enough for everything to fit nice

basically trial and error, best way

Mines one of the big fmic's and quite thick.

I didnt do it, a workshop that does not exist anymore did, but they barely shaved anything off it. didnt look so hard to do, mind you I didnt know much about my car at that stage.

you can barely notice it, cops have to stick their heads under the license plate to see it. I rekon it looks good. :)

I think yours is the factory front bar and mine is the factory body kit? not 100% sure...

SL370681smaller.jpg

3321765505_503c3783fd_o-1.jpg

SL370746smaller.jpg

You have M-Spec and the OP just has the normal front bar :)

My S1 Front bar had working driving lights (which from what I've heard is pretty rare) so they were in the way thats why my cooler was angled lol but anyway

Series 2 front bar is much nicer to put a FMIC behind, Requires a fair bit of trimming but only of parts that you cant see

there are also plenty of return flow front mount intercooler kits that you can use which sit very well as they use the stock intercooler pipes in the engine bay.

I have a BLITZ LM Return flow one, but i have a series 2 front bar, sits perfectly flush and its black too so does not grab any un-necessary attention.....

Just a thought. Oh yeah and you dont need to cutt any holes in the engine bay, just a slight few cms off the back of my front plastic bar and thats it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...