Jump to content
SAU Community

How To Install Walbro Gss-341 In An R34?

Hanaldo

By Hanaldo,
in Engines & Forced Induction

 Share

Recommended Posts

stranger12 Community Regular

stranger12

Posted
Posted (edited)
On 27/08/2010 at 1:33 PM, TriniGT said:

When I replaced my pump with a walbro it did not give the full pressure, I had to rewire using the stock wires as the feed for the relay and after that was done my walbro would sing as the voltage was was where ti should be. My fuel pressure was spot on after that. Before that my pressure was around 20psi so I am sure there is some sort of varying voltage causing this.

how did you know what your pressure was? pressure regulator or in car sensors?

 

also for negative feed to relay and pump, do you take it from battery negative terminal or body of the car ?

Edited by stranger12
  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • EndZee
      Rb25det s1 igniter pin out

      By EndZee · Posted

      Hello, im asking about this guy - coil igniter on rb25det series 1 r33 s1 engine. I need to know if pins on coil side indicate coils itself from 1-6 or it’s firing order so pin nr1 goes to 1st fired spark plug:(1pin-1firing spark, 2pin-5order firing spark, 3-3, 4-6, 5-2, 6-4…)   photo: https://files.fm/f/k9pdug38uq
    • GTSBoy
      Powder coat on mating surface

      By GTSBoy · Posted

      Remove it. Certainly from the hub face. I'm not in love with leaving it on the wheel assembly surface either - but if it is common to do so, then....maybe fair enough. It's not difficult. Just time consuming. For the hub face you just need a large enough block and suitable grades of abrasive paper to get it off flat. The same would be true of the assembly face. Just more time consuming, probably needing a lot more care. It's defo going to be easier just to assemble the wheels as is, seal them up, and check them periodically to see if there's any movement or loosening of the fasteners, than it will be to remove it though.
    • dyl33
      Powder coat on mating surface

      By dyl33 · Posted

      Hello, I got my wheels powder coated and they've powder coated bloody everything the mating surface and hub (even told them not to lol) anyway should I leave it or remove it. (Would be very hard) I've searched a lot and lots of powder coaters don't mask the mating surface but do mask the hub surface. How bad it powder coat on the mating surface or hub? My question is what should I do?
    • dbm7
      R34 Gt Auto Tuning

      By dbm7 · Posted

      Yeah, R34 with RB25DE likely has a 4AX01 box in it, which is a medium duty auto ~ with the RB25DET mill, it would've been fitted with 4AX00 (4AX13) heavy duty build (same case, different internals). An RB25DET will lunch on a medium duty 4R01 auto in pretty short order ...to give you some visual idea of differences between the 'medium' and 'heavy duty' boxes, you only have to look at the 2/4 band for comparison...it's chalk and cheese...(plus bigger high clutch, extra pinion in the planetary sets, higher oil pump output, different bearings, higher TC stall speed )... You can control them with just about any aftermarket TCU for electric-over 4-speed with TC lockup clutch (ie; the GM 4L60E and others)...I have a custom standalone TCU that includes MAP sensor (for turbo applications) along with TPS, RPM, and line pressure monitoring...in other words, I don't use any ECU signals...no real need to.
    • GTR ZOAH
      S A U N S W Club Membership

      By GTR ZOAH · Posted

      Welcome 😉
×
×
  • Create New...