Jump to content
SAU Community

Recommended Posts

And WTF are they doing. 39.9% is not full, so it is rather irresponsible to lighten restrictions going into spring/summer...

The north south pipeline was switch on this year, so that's probably part of the decision

Edit: Ahhh yeah... what Greg said ^^^

The only thing stopping me from washing my car now is time :D Too freaken busy :O

You have listed a Supra / 300ZX / MR2, which are the cars you "did" have, you would be busy washing 3 cars on your own.

:(

You have listed a Supra / 300ZX / MR2, which are the cars you "did" have, you would be busy washing 3 cars on your own.

:(

Yeah, I need to change that :D Just refer to my sig for my car list.

You can now wash your car at home using a bucket or a high pressure cleaning device

- You cannot use a hose to wash your car

- You can of course use rainwater as you could under all stages of restrictions

This change has been made possible through a combination of factors:

- Melburnians commitment to water conservation the community has saved an additional 34 billion litres since the start of the voluntary Target 155 campaign. Melburnians have used just under 150 litres per person since the target 155 campaign commenced, a tremendous result.

- New sources of water are now on line and these add a new level of security and include the Tarago Reservoir and the North South Pipeline

- We have had much better rains. We had enough rain in Autumn to thoroughly wet the catchments and with the good winter rains storages are rising at over 1% per week. Currently our water storages are ~12% higher than the same time last year which equates to about six months consumption.

- Work on the new Desalination Plant at Wonthaggi is progressing very well, with completion still on track for late 2011. The desal plan will add another 150 Billion litres per annum which is about 42% of current annual water usage

I think if i hooked up my high preasure hose people walking the street would give me dirty looks just like when i washed my dirt bikes with it.. there like WTF ARE YOU DOING?!?! SAVE THE WHALES

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Just get rid of the orignal low impedance injectors, replace with modern high impedance injectors, and you won't need the resistors. Wire direct, as per any other engine.
    • Tao, we're not talking about the ECU boost ref. We're talking about the wastegate signal source.
    • Flapping up and down is a consequence of the varying pull on the belt. When the engine speed is suddenly increased, the tension in the belt increases too. When that engine accel changes to decel, the tension is reduced and turns up as a little extra length of beltes between the pulling and dragging pulleys. That extra length flaps up, then down. There's all sorts of other harmonic stuff going on too.
    • hello ladies and gentlemen so i’ve swapped a rb26dett into my r33 gtst and ive come across many speed bumps but its nearly over what im having issues with is the injector resistor box that are normally on the RB26 fuse box but im still using my rb25 fuse box and as a result my injectors aren’t getting power and is the last thing i need to figure out so the car can start. can anyone help me out on where i can find a wiring diagram for the rb26 harness to see where the injectors are supposed to receive power 
    • The boost pressure at the compressor cover will be higher than at inlet manifold. lets say, trying to hold 20 psi flat at 7000 RPM. If your wastegate opens at 20 psi measured at the compressor cover, the engine may only be seeing 16 psi. Your base pressure reading at engine would be 20psi by 4K and 16psi by 7K while your MAP at compressor housing still reads 20psi at 7K. For this reason your ECU's MAP source is never on the compressor cover. This difference isn't a major concern if you're using an electronic boost controller (EBC).
×
×
  • Create New...