Jump to content
SAU Community

Recommended Posts

What can people suggest in the way of cheap semis, new or second hand, for 235 17's I bought a learner set from Donnelans a while back and they were only $260 delivered to Albury, granted they were nothing special condition wise but they've done me alright for 3-4 track days to learn on. I'm happy enough in my braking and the balance of the car that I can afford to buy some better second handers or maybe even something new as I won't be flat spotting them hopefully.

I'm also after cheapy Toe Arms for the S13, I've used ISC rear camber arms and they were decent for the money. His toe arms are about 180 and I've seen sets on ebay for around $100, not sure on quality though.

Given the car is only a CA and doesn't run blistering laps times it's not going to be critical but has anyone had any experience with anything cheaper than the isc items?

Edited by ActionDan
Link to comment
https://www.sau.com.au/forums/topic/334146-cheapo-semis-and-toe-arms/
Share on other sites

The KU36's seem to be quite popular, though not a semi slick, but I'm guessing that lap times on a new set of those would be similar and possibly better than what I'm getting on these thrashed semis. Is there a semi that's comparable cost wise?

The KU36's seem to be quite popular, though not a semi slick, but I'm guessing that lap times on a new set of those would be similar and possibly better than what I'm getting on these thrashed semis. Is there a semi that's comparable cost wise?

I was still considerably faster on thrashed re55's than i was on fed 595rs's. Unless you have AO48's, then yes, all rounders will be faster if the semis have been heat cycled a fair bit. The kumho semis would be the pick of the cheap ones but you are still looking at 1300ish. Personally i'll never bother with r888's again, they are around the same price.

On the toe arms front, I've seen 2 isc arms snap at welds. I wouldn't use them, or anything cheaper for that matter. I use D project camber and toe arms in my track car, cheapish and the quality is ok. They seem to be holding up too, plus replacement rose joints are available. Camber arms are about 3 years old now with many track days and toe arms have survived 7 or 8 track days.

Interesting in the differing opinions. the KU36 thread seemed to have some OK results when compared to flogged semis, which mine are.

The other option is finding some half decent second handers. Being heat cycled a few times from what I thought just makes the compound harder so longer to get up to temp and less grip but also harder wearing?

Edited by ActionDan

I do have two sets of rims, but I only use one set on the track and the car is pretty much track only so I can use whatever tyres I want. The street rims are just plain 5 spoke 17's with the tyres that came on the car. The track rims are 9" volks with 235 semis.

http://www.cazmanindustries.com/

he makes super high quailty parts. cost a little bit more but are full rebuildable and wont break. send him an email and see what he says.

he's highly recommended on nissansilvia.

ahh yeah I nkow Caz from NS. Good idea.

MArlin, where were you going with that second set of rims comment? I'm not worried about burning up tyres on the street as I dont street drive very often and when I do it has street rims/tyres. So I can leave my semis on the track rims. What are the mini ones setting you back and what size?

I've used the Mini ones for 270klm at Lakeside so far (at 10/10ths), and the worst of the four is maybe one third worn.

They were virtually new (maybe 5/6 laps) when I got them and they cost me $100 each plus some freight to me from Melbourne. I since found I can get in Bris for $75 each. LOL

Dan, two sets of wheels means you drive to the track and bolt on the second set that were in the boot and back seat with proper race tyres, slicks even. IMO you are over-wheeled with 9 inch rims on that car.

The Mini Challenge tyres are Dunlops, size is 215/45/17, but I measured them because they looked so much bigger, and turns out they are nearly identical in size and width to my Dunlop and Kuhmo 235/45/17's.

Edited by Marlin

I dont need to do that as the car gets towed to the track so the track rims and tyres stay on :)

That's awesome value!

I think you should PM me some details on where I can hook up with those :thumbsup:

Correction 8" fronts (or are they 8.5's? can't remember) and 9" rears. For the cost of the rims I couldn't say no. A bit of extra rim width is fine to me, they take the 235's well with nice straight sidewalls, none of this drifter stretched habib shizzle going on.

Hook me up Ben :D If they're as wide as you say they would be perfect for my car.

Awesome, thanks. If they're as wide as you say then they should fit my 9" rears without issue also. Just to confirm, you comapred your 215 mini tyre to a 235 Dunlop and Kuhmo semi or road tyre? What model is the mini tyre?

I placed them beside both 235/45/17 Kuhmo KU36 road tyre and Dunlop O3G road/race tyre and they are virtually itendical in width, so they are a 'big" 215.

I make no promised re the suitability to 9" rim.

This Dunlop slick has no info other than "Dunlop" and a big bunch of Japanese text. I suspect they are imported specifically for the Mini Challenge.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
×
×
  • Create New...