Jump to content
SAU Community

Recommended Posts

I'm thinking about a Y-pipe and a Cobb. 13 months after buying the car I reckon it needs more.

How much should I pay for labour to fit a Y-pipe in Sydney?

Any suggestions about a good place to have this done?

Col Crawford Brookvale does it for $100.

Link to comment
https://www.sau.com.au/forums/topic/334844-y-pipe/#findComment-5426142
Share on other sites

As an Authorized Cobb Tuning Pro Dealer, we can supply your Cobb AccessPort for $1199.00 and can offer professional in-house installation.

As far as Y Pipes go, we stock Blitz, Kakimoto, Dodson Motorsport and JJR Y Pipes, starting from $499.00 :)

For more information, have a look at our website at http://justjap.com/store/home.php?cat=403 or call us on (02) 9545 0532.

Cheers,

Steve

Link to comment
https://www.sau.com.au/forums/topic/334844-y-pipe/#findComment-5427142
Share on other sites

is the map willal provides any different to what the cobb tuning website offers for ADM cars?

mid-pipe is a great mod, somewhat warranty friendly, and makes the sound come alive

From what I have read it is different. I am going to try and get the willall tune emailed to me tomorrow and install it before we catch up however if it doesn't arrive in time I'll just be running the stage 2 Cobb tune.

Link to comment
https://www.sau.com.au/forums/topic/334844-y-pipe/#findComment-5439191
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Saw this video today from Adam LZ.    Long story short is he is claiming that the load from the engine fan once the fan clutch heats up(engaged) is increasing the getrag rattle(at idle) when you don't have a dual mass flywheel.  Before I go buying an electric fan setup .... Anyone heard of this ?    I must admit when my car is cold the getrag is pretty quiet and I do notice the rattle after it is all warmed up. I've always assumed this is due to the gearbox oil temp and tolerances of metal.       
    • Yep it sure does.   Tone wheel lines up in the same spot perfectly.    
    • Something I meant to say when we were chatting the other night about having an open trailer floor being great to work on a car, but you've never used the feature... It's a great place to park a car after doing suspension component changes, and do the tightening of all the bushes with the car sitting at full ride height. Especially when you don't have a 4 post hoist!
    • That is way more science than even I would use. I just eyeball it, not even accounting for the non-verticality of the tape measure when held on the lip and the centre at the same time. +/- 2mm is good enough for the girls I go out with.
    • So, before putting them in I need to understand the stock ride height. This is how I measured it: First, check the diameter of the wheel's centre cap, it was 52mm. Then put a piece of masking tape approximately across the centre and measure 27mm (half) from at least 3 sides to get a reasonable idea of the centre of the wheel cap. Mark that with a horizontal line as one measuring point. Then, directly above the wheel on the guard, put another piece of masking tape in approximately the centre. Use a string line to find out the point on the guard above the centre of the wheel cap and mark that. Then it is simple, just a tape measure to check the distance from centre of the wheel to the centre of the guard. Final results where  LF: 381mm RF: 379mm LR: 401mm RR: 400mm Pretty even considering they are 120,000klm old factory springs, lets call that 380 front and 400 rear.
×
×
  • Create New...