Jump to content
SAU Community

Recommended Posts

Hi guys,

At the last DECA I was giving the car a workout and found that the steering developed an intermittent dead spot in the centre. I had the passenger grab the wheel at one stage to prove I wasn't going crazy.

The car is an S13, CA, and I'd assume it's the original rack, it certainly doesn't look reco'd. I'm assuming rack as the tie rod ends looked fine, no bends, threads are good, no free play that I can easily get to happen up on stands. Rack mounts and bushes "look" OK to me but I'm no steering specialist. I topped up the power steering reservoir and thought it got better but then it came back, it seem to be when loading the car up hard side to side on the skid pan, which to me implied a hydraulic issue in the rack. The boots on the end of the rack aren't filled with fluid so I'd say the seals at the end of the rack are good, no leaks that I can see.

At it's worst there's probably a good 20-25 degrees dead space in each direction from centre.

I had 235 semi's on it at the time, -2.5 deg camber. Can't recall toe/castor settings right now.

Thoughts?

you need to determine where the freeplay is exactly. jack it up and get some one to turn the wheel in the freeplay back and forth and check everything,

what colour is the powersteer fluid? is it burnt?

It's on stands at the moment and I'll be doing that but when it was intermittent and seemed relative to lateral load on the car durnig cornering.

Fluid is standard colour, didn't look any different to what came out of the bottle when I topped it up and didn't smell burnt.

I'll be getting under it in the next few days.

OK here's what I found.

Car up on stands, me lying on my bak with the leadlight, GF turning the wheel.

Mechanically I can't see any free play, I had the GF do fast and slow turns full lock in both directions with and without me providing enough resistence on the wheels to stop her being able to turn the wheel in the cabin.

I also had her hold the wheel hard while I tried to make each wheel turn, no freeplay there.

What I did find is that one rack boot has a split in it and inside I can see brown grease. Without cmoparing to the other one I'm not sure if it should be that colour or not. If it shouldn't be covered in crud then I suspect that when the rack has a lot of pressure on it there may be fluid getting past the outer seal and into the boot, however the boot didn't show signs of large amounts of fluid - maybe early days for the leak.

I also noted that the inner part of the tie rod where it joins the rack has been bent back, I'd say from hitting the rack on full lock turns too hard.

I also note that the outer tie rod ends/pins that connect to the wheel hub assembly have split boots on both sides. I'm a bit vague on terminology, sorry.

Thougths? Mechanically it looks and feels ok. A mate was telling me there's a valve where the steering column knuckle joins the top of the rack and they are common failure points just for something extra to consider.

Thanks so far guys :D

A bent rack end will cause that, as it spins around it can play havok, but unlikey due to your diagnosis.

If you don't know how to diagnose problems its hard to rule anything out.

There are only a few links in the steering (5 if you count the rack bushes)

Jack it up, grab the wheel at 3 and 9 o clock. Keep steering the tyre back and forth by hand, If you feel any freeplay, your getting somewhere. Get a mate to do the same while you watch closley at each steering part to see whats got free play.

To me it sounds like the rack is stuffed, Ive never heard of the gears loosing a tooth, but it might be possible.

Could also be a caster rod bush/bearing gone, it might be binding the steering.

To test your rack bushes put it on the ground, get 5 fat mates to sit in the engine bay, then you get under the car and watch the rack while your girlfriend steers left to right throughout its whole range.

5mm of movement is normal, any more or abnormal movement is a bad sign, as under load with semis the problem compunds.

Really its impossible to diagnose over the internet.

This leads me to believe the outer seal in the rack is weeping under pressure? I assume this requires a rebuild?

Bad side

post-23873-1283656656_thumb.jpg

Good side

post-23873-1283656694_thumb.jpg

Edited by ActionDan

also, check the drivers side rack bush. it is usually covered in oil and perished. with the car on the ground jiggle the steering wheel. you will be able to see the rack move side to side if it is worn.. this can feel like freeplay when driving.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...