Jump to content
SAU Community

Recommended Posts

Hi guys,

At the last DECA I was giving the car a workout and found that the steering developed an intermittent dead spot in the centre. I had the passenger grab the wheel at one stage to prove I wasn't going crazy.

The car is an S13, CA, and I'd assume it's the original rack, it certainly doesn't look reco'd. I'm assuming rack as the tie rod ends looked fine, no bends, threads are good, no free play that I can easily get to happen up on stands. Rack mounts and bushes "look" OK to me but I'm no steering specialist. I topped up the power steering reservoir and thought it got better but then it came back, it seem to be when loading the car up hard side to side on the skid pan, which to me implied a hydraulic issue in the rack. The boots on the end of the rack aren't filled with fluid so I'd say the seals at the end of the rack are good, no leaks that I can see.

At it's worst there's probably a good 20-25 degrees dead space in each direction from centre.

I had 235 semi's on it at the time, -2.5 deg camber. Can't recall toe/castor settings right now.

Thoughts?

you need to determine where the freeplay is exactly. jack it up and get some one to turn the wheel in the freeplay back and forth and check everything,

what colour is the powersteer fluid? is it burnt?

It's on stands at the moment and I'll be doing that but when it was intermittent and seemed relative to lateral load on the car durnig cornering.

Fluid is standard colour, didn't look any different to what came out of the bottle when I topped it up and didn't smell burnt.

I'll be getting under it in the next few days.

OK here's what I found.

Car up on stands, me lying on my bak with the leadlight, GF turning the wheel.

Mechanically I can't see any free play, I had the GF do fast and slow turns full lock in both directions with and without me providing enough resistence on the wheels to stop her being able to turn the wheel in the cabin.

I also had her hold the wheel hard while I tried to make each wheel turn, no freeplay there.

What I did find is that one rack boot has a split in it and inside I can see brown grease. Without cmoparing to the other one I'm not sure if it should be that colour or not. If it shouldn't be covered in crud then I suspect that when the rack has a lot of pressure on it there may be fluid getting past the outer seal and into the boot, however the boot didn't show signs of large amounts of fluid - maybe early days for the leak.

I also noted that the inner part of the tie rod where it joins the rack has been bent back, I'd say from hitting the rack on full lock turns too hard.

I also note that the outer tie rod ends/pins that connect to the wheel hub assembly have split boots on both sides. I'm a bit vague on terminology, sorry.

Thougths? Mechanically it looks and feels ok. A mate was telling me there's a valve where the steering column knuckle joins the top of the rack and they are common failure points just for something extra to consider.

Thanks so far guys :D

A bent rack end will cause that, as it spins around it can play havok, but unlikey due to your diagnosis.

If you don't know how to diagnose problems its hard to rule anything out.

There are only a few links in the steering (5 if you count the rack bushes)

Jack it up, grab the wheel at 3 and 9 o clock. Keep steering the tyre back and forth by hand, If you feel any freeplay, your getting somewhere. Get a mate to do the same while you watch closley at each steering part to see whats got free play.

To me it sounds like the rack is stuffed, Ive never heard of the gears loosing a tooth, but it might be possible.

Could also be a caster rod bush/bearing gone, it might be binding the steering.

To test your rack bushes put it on the ground, get 5 fat mates to sit in the engine bay, then you get under the car and watch the rack while your girlfriend steers left to right throughout its whole range.

5mm of movement is normal, any more or abnormal movement is a bad sign, as under load with semis the problem compunds.

Really its impossible to diagnose over the internet.

This leads me to believe the outer seal in the rack is weeping under pressure? I assume this requires a rebuild?

Bad side

post-23873-1283656656_thumb.jpg

Good side

post-23873-1283656694_thumb.jpg

Edited by ActionDan

also, check the drivers side rack bush. it is usually covered in oil and perished. with the car on the ground jiggle the steering wheel. you will be able to see the rack move side to side if it is worn.. this can feel like freeplay when driving.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...