Jump to content
SAU Community

Recommended Posts

the only diffrences in Group A blocks (O5U)and standard older type RB26 blocks are one water jacket is enlongated....this can be done to the older block all R34 blocks have this O5U type block

*edit*Actually...it may be O9U.....i have to check my RB26 history book....its out on loan at the moment....

Link to comment
https://www.sau.com.au/forums/topic/33589-nismo-n1-block/#findComment-672902
Share on other sites

The information you've been given so far is incorrect.

There are 3 different blocks: cast into the side of the block are the letters

05U or 24U

The std. blocks tend to crack bores when you exceed 550 to 600HP.

The STANDARD BLOCK 05U is a thin wall casting, due to the larger water jackets around the bores. (comes third for desirability)

The N1 and all R34 v-spec 24U is a thick wall casting and has the smaller water jackets around the bores. (comes second for desirability)

The GROUP 'A' BLOCK 05U but is a thick wall casting and has the smaller water jackets around the bores. (comes first for desirability, but rare)

Look for a block with the smaller water jackets, near the treaded holes for the head bolts.

You can buy the N1 block from NISSAN at around $3400.

Phillip

p.s. You can also get fully sleeved blocks.....but thats another story.

Link to comment
https://www.sau.com.au/forums/topic/33589-nismo-n1-block/#findComment-674573
Share on other sites

Just some info from http://www.pow.com.au/gtr_engine_specs.htm

Race_block_sml_blk.jpgSpecial_Race_block_sml_blk.jpg

This is an ex-Bathurst Group A heavy wall block.

When GT-R engines make big horsepower (600hp+), they have been known to split the standard block. You may be wondering why the inside of the block is white in color ?

It has been sealed with an epoxy coating so that the oil drains back fast and bits of cast iron cannot break from the inside of the motor and go into the oil system. The welsh plugs holes have been tapped, the original welsh plugs removed and replaced with screw in machined aluminium ones to prevent them from ever popping out when under pressure.

This block is a very very rare item. These heavy wall blocks are not available anymore and are irreplaceable!

Link to comment
https://www.sau.com.au/forums/topic/33589-nismo-n1-block/#findComment-679602
Share on other sites

  • 3 years later...
The information you've been given so far is incorrect.

There are 3 different blocks: cast into the side of the block are the letters

05U or 24U

The std. blocks tend to crack bores when you exceed 550 to 600HP.

The STANDARD BLOCK 05U is a thin wall casting, due to the larger water jackets around the bores. (comes third for desirability)

The N1 and all R34 v-spec 24U is a thick wall casting and has the smaller water jackets around the bores. (comes second for desirability)

The GROUP 'A' BLOCK 05U but is a thick wall casting and has the smaller water jackets around the bores. (comes first for desirability, but rare)

Look for a block with the smaller water jackets, near the treaded holes for the head bolts.

You can buy the N1 block from NISSAN at around $3400.

Phillip

p.s. You can also get fully sleeved blocks.....but thats another story.

hey mate ive got a n1 block

in perfect condition

ho muchcan i get rid of it for u recon

im tryin to get rid of it atm

ur saying $3400 brand new form nissan this block looks like its never been used

???

i know its a n1 block because it has 24u on the side of it..

Link to comment
https://www.sau.com.au/forums/topic/33589-nismo-n1-block/#findComment-3550333
Share on other sites

hey mate ive got a n1 block

in perfect condition

ho muchcan i get rid of it for u recon

im tryin to get rid of it atm

ur saying $3400 brand new form nissan this block looks like its never been used

???

i know its a n1 block because it has 24u on the side of it..

You've opened 3 threads today asking the same question, stop spamming as you have already had your questions answered a number of times.

Link to comment
https://www.sau.com.au/forums/topic/33589-nismo-n1-block/#findComment-3550336
Share on other sites

Man some ones going to buy the wrong block.

05U standard block

24U N1 block can be brought for $2500 from sau traders and dont think all R34 vspecs came with one.

RRR GT block best you can buy if you can find one dont go looking for change from $5000.

Brad.

Link to comment
https://www.sau.com.au/forums/topic/33589-nismo-n1-block/#findComment-3550737
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...