Jump to content
SAU Community

R34 Turbo Op6 Perfect Condition

Harey
 Share

Recommended Posts

Harey Veteran

Harey

Posted
Posted

Hey all,

I just had my turbo pulled off my R34 GT-T. It is the factory R34 turbo with OP6 rear housing.

It is in perfect condition, no shaft play at all.

Located in Richmond, Melbourne.

$350

Jeff 0400648813

I will take some photos tomorrow

Link to comment
https://www.sau.com.au/forums/topic/337304-r34-turbo-op6-perfect-condition/
Share on other sites
Harey Veteran

Harey

Posted
  • Author
Posted

Here are the promised pics!

Car has just clicked over 96,000kms and is in very good condition. Turbo was performing great and made 190rwkw on only 10psi dropping to 9psi. Only reason I took it off was that I am on the hunt for big power.

Happy to post.

post-29432-1284955431_thumb.jpg

post-29432-1284955443_thumb.jpg

post-29432-1284955447_thumb.jpg

chiksluvit Experienced

chiksluvit

Posted
Posted (edited)

high flowed R34 turbos make more power than high flowed R33 turbos, it has bigger exhaust housing

you'll need to put up with a little bit more lag but nothing major, tuned well it should peak around 20rwkw more or so than R33 high flow

Edited by chiksluvit
Harey Veteran

Harey

Posted
  • Author
Posted
when you say laggy... it still wouldnt be as laggy as a 3076...

also is the nissan 6 bolt stud pattern the same for r33/r34 ?

My understanding is that the OP6 housing is smaller then the 0.63 housing of the GT30 series so will definitely not be as laggy as a 0.82 on a 3076.

Yes the nissan 6 bolt stud pattern is the same for r33 and r34. 'Chicksluvit' runs an R34 hiflowed turbo on his R33.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • funkymonkey
      Most women will agree that parking is the most taxing part of driving

      By funkymonkey · Posted

      Are you meant to double fist them?
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
×
×
  • Create New...