Jump to content
SAU Community

Next Mods I "need" To Buy...

Bubbafaguchi

By Bubbafaguchi,
in Australian Capital Territory

 Share

Recommended Posts

Bubbafaguchi Enthusiast

Bubbafaguchi

Posted
Posted

hey guys,

im after a set of aftermarket shocks and springs. i want coil overs but i dont think ill have the money for em. if anyone has anything like that even if there coil overs let me know as i just came back from a coast trip which involved the clyde... so my blue beast need to handle better.

Cheers Jason

Link to comment
https://www.sau.com.au/forums/topic/337562-next-mods-i-need-to-buy/
Share on other sites
Bullet32 Veteran

Bullet32

Posted
Posted

My advice:

Don't make the mistake of buying second hand suspension Jason - especially if you want your Skyline to handle really well. You don't know what your'e buying and whatever you get may need rebuilding anyway, so you end up spending the same or more than if you were to buy brand new.

Your best bet is to check the group buys on these forums, there are usually really good deals there... Or contact one of the site sponsors to see if you can get a discount.

Also, remember that your Skyline is now 14 years old and if you replace the shocks and springs, it will most likely need new bushes as well.

By the way - The single best handling mod you can do to a GTS-T is to get a HICAS lock-out kit fitted.

Hope this helps

Mick :ninja:

Bubbafaguchi Enthusiast

Bubbafaguchi

Posted
  • Author
Posted

cheers man.

everyone ive talked to so far has said the same thing in a nut shell. and as such a mate is offering my some brand new teins for a hugely discounted price... its just raising the money for the discounted price is whats killing me hahaha. how much does a lockout kit cost? and i figured id need new bushes as well i was just dodging it :) anywhere good i can go to or that is recommended to get this type of work done?

once again cheers

Jason

zebra Grand Master

zebra

Posted
Posted

Lockout kits can be had for ~100 bucks, Fitting them can be a massive pain, as the rod ends are bloody tight.

What model Tien's were you looking at, some of them are horrid, some are good, I wouldnt go anything more than Super Streets for a street skyline, the rest of the Tien line up is mainly drift/circuit orientated, So not much good for Aussie back roads.

A Set of BC Racing's with some softer "swift" springs could be a good thing and probably still come out cheaper than the Tiens.

Or if you have the budget a set of "Aus Spec" Bilstein B6's with Custom springs to suit (once again Swift Springs are recommended to me by nearly everyone I know who races)

Then as a must have, get some aftermarket swaybars under the thing, will make the car feel much better than just some stiffer springs/shocks,

Big swaybars and soft springs is what works on a street car.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...