Jump to content
SAU Community

Hks Gt2530 Twin Turbos Eqv Garrett -5 Denso 720cc Injectors Used 87mm Cp Pistons

newlife
 Share

Recommended Posts

newlife Contributor

newlife

Posted
Posted

mint condition pair of hks gt2530 pair. tiny bit of shaft play..u cant feel it. never seen bore than .8bar. looks brand new. without actuators.

$2100 delivered anywhere in aus. pay pal accepted but surcharges applies.

Denso 720cc direct drop-in injectors for rb26 prefect working order $600 delivered

used rb26 87mm cp pistons only used for one dyno run $700 delivered

cheers Sam

blacksheep7 Newbie

blacksheep7

Posted
Posted

Just a feeler here, but how can you tell theres any shaft play if you cant feel it?

more importantly, I hear since theyre ball bearing instead of thrust bearing you need an oil feed reducer to install these, is that included?

also would you ship to the frozen wastelands of Canada? god.. how much would that cost?

ryanelmi Contributor

ryanelmi

Posted
Posted

hey mate.. i have a gtr with -5 turbos and i need to upgrade my injectors will these be sufficient for around 1.5 bar? also will they fit directly in the fuel rail without modification like the nismo ones? i cant send pms so if you can send me a pm with your phone number i will contact you and make a payment online..

  • 2 weeks later...
murrayis Mentor

murrayis

Posted
Posted

Hi,

I finally got the turbos.... They came from Sri Lanka!!!!! And to my disgust they are not the turbos from the pictures or info provided!

What the hell mate?

These are the turbo’s I just received!

post-23119-1286415470_thumb.jpg

post-23119-1286415486_thumb.jpg

post-23119-1286415499_thumb.jpg

An explination would be great Sam!

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

Not sure what the bank is gonig to do exactly after you have EFT'd the money through.

Your only option is to contact the local state authorities.

Buyer beware guys.

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • albyz34gt
      34 de+t conversion using s2 stagea automatic transmission, engine harness and ecu

      By albyz34gt · Posted

      Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Duncan
      R32 GTS (RB20DE) Injectors Replacement

      By Duncan · Posted

      Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • GTSBoy
      Wheel Sizes & Offsets For Skylines

      By GTSBoy · Posted

      There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • GTSBoy
      Rear Sway Bar Busshings - Holden Astra TS (2002)

      By GTSBoy · Posted

      I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...