Jump to content
SAU Community

Recommended Posts

Hey Guys,

I need some help here with my ECU choice.

I have a Motec M800 + Motec CDI that I am running in one of my race cars. Great ECU, very happy with the tune and control - NOT HAPPY about paying for bullshit extras that should be included (launch control, anti lag, logging etc). I have the basic setup and logging enabled and advanced functions is around $500 on top, which I will buy for anti lag and launch control when the car is finished after the new turbo install.

I can spend cash and and get a new loom made up for the daily drive and just have the motec plug in and plug out whenever I need to get the race car sorted. I can only drive one car at a time so this is fine, however I was thinking that a VIPEC V88 would be a good upgrade for the daily, cost around $2500 or so trade with sensors etc and I get all the goodies factory (anti lag launch control etc).

Just how good is the V88? Is it as good as or better than the motec? The software looks easy to follow and there are heaps of options enabled as well as factory additions that increase the functionality. I would like to try something new like the VIPEC in the future anyway and my conversion/switching costs is around $1000 for a new Motec flying loom + CDI Loom + 3bar map sensor and a few other basic sensors to make it plug and play. So for around $1500 after switching costs, I get a new ECU and a new toy to play with, with all the features that would cost THOUSANDS to enable on a motec.

What are your thoughts?

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

I have considered Autronic, but it is too archaic for my liking and the software sucks.

The newer haltech platinum did cross my mind as well. Software looks fancy, however not sure on the tune/functionality - anyone got feedback on the newer haltech?

i removed my m600 and cdi and now run a vipec v88 and m&w cdi in the godzilla drag gtr ...runs the engine the same..

if it was not up to the job i would not run it on my 30grand engine..

hope this helps. mark godzilla motorsport..

Hey Guys,

I need some help here with my ECU choice.

I have a Motec M800 + Motec CDI that I am running in one of my race cars. Great ECU, very happy with the tune and control - NOT HAPPY about paying for bullshit extras that should be included (launch control, anti lag, logging etc). I have the basic setup and logging enabled and advanced functions is around $500 on top, which I will buy for anti lag and launch control when the car is finished after the new turbo install.

I can spend cash and and get a new loom made up for the daily drive and just have the motec plug in and plug out whenever I need to get the race car sorted. I can only drive one car at a time so this is fine, however I was thinking that a VIPEC V88 would be a good upgrade for the daily, cost around $2500 or so trade with sensors etc and I get all the goodies factory (anti lag launch control etc).

Just how good is the V88? Is it as good as or better than the motec? The software looks easy to follow and there are heaps of options enabled as well as factory additions that increase the functionality. I would like to try something new like the VIPEC in the future anyway and my conversion/switching costs is around $1000 for a new Motec flying loom + CDI Loom + 3bar map sensor and a few other basic sensors to make it plug and play. So for around $1500 after switching costs, I get a new ECU and a new toy to play with, with all the features that would cost THOUSANDS to enable on a motec.

What are your thoughts?

you say it's for a daily.... why not just go a good old second hand pfc?

vipec/motec are definately better ecu's but when you have a race car, how much do you really need on the street?

JJJ: engine is a 1.5JZ, PFC for a 1JZ is around 1500 or so - not worth it for such a limited ECU that is limited to a hand controller. FC datalogit software will bring it up close to the cost of a V88. Looking at making around 350rwkw with a T04Z and HKS 264/272 cams and I'll borrow the 800cc injectors while I upgrade the fuel system on the race car for E85.

Walk510: Yes the factory motec datalogging software is great, but if you want to overlay graphs etc - you need pro, more $$$.

Sounds like the V88 is a winner for a race/daily setup. I love the Motec, but it does come at a high premium with marginal added value compared to today's ECUs tune and standard features. Fantastic back in 2001, but its 2010 now and there has been a lot of inroads into ECU tech to try and beat Motec at their own game.

Motec themselves are working on ECU's to tune direct injection and so forth - the next generation of engines.

Currently waiting for quotes on a flying loom and so forth to see how much it would cost to re-wire the CDI and Motec instead of getting a new ECU, however I believe that this exercise could cos as much as a v88 in itself given today's prices.

On another note - what is the v88 knock sensor option like? How does it compare to the Gizmo k-mon?

You already have the motec and it is $500 for the extras but a Vipec is worse and costs $2500? Why on earth would you pay more for less? Am I missing something here?

A Motec is 1000x better and easier to tune properly than any other ECU on the market, and if it is going to cost less for the extras then I don't see why you would downgrade to something else. Personally if you already have made the outlay and paid for installation and tuning I would not change.

If you were considering both from scratch then I would cost up both options and consider the Vipec. How many of the extra features would you need? Do you really need launch control etc?

Edited by Rolls
You already have the motec and it is $500 for the extras but a Vipec is worse and costs $2500? Why on earth would you pay more for less? Am I missing something here?

Lol... Yes, a lot.

The fancy logging with the Motec is impressive and the reason why a lot of people still use them. The Vipec will get there but it is still a new product and is continuing development.

Lol... Yes, a lot.

The fancy logging with the Motec is impressive and the reason why a lot of people still use them. The Vipec will get there but it is still a new product and is continuing development.

I realise the vipec is a great ECU but the motec is still better if he already owns it then I am confused why spending more to get less is being considered?

I realise the vipec is a great ECU but the motec is still better if he already owns it then I am confused why spending more to get less is being considered?

How is the Motec better? Better at what? Vipec has a faster processor and is more accurate, operates at greater temperature extremes... do some reading or at least drive a car tuned with an M800 and one with a V88.

He could sell the M800 with everything and get a V88 with all motorsport options, installed and tuned for the price he sold it for.

A Motec has far superior tuning software, Ive used a few and nothing even comes close. If he does sell the motec will he get many extra features that will be used? If not I would stick with the motec purely due to how much easier they are to tune.

Edited by Rolls
If not I would stick with the motec purely due to how much easier they are to tune.

That is surprising, not in my experience. But each to their own.

To the OP Vipec V88 uses the standard knock sensors, works fine.

That is surprising, not in my experience. But each to their own.

To the OP Vipec V88 uses the standard knock sensors, works fine.

Yeah I've changed my tune after a bit of reading, by the time you buy the wideband support, knock sensor support blah blah it certainly is going to be prohibitive to buy. I think the Vipec would be better bet even if it isn't as easy to tune, but I guess that comes down to the tuner anyway.

How is the Motec better? Better at what? Vipec has a faster processor and is more accurate, operates at greater temperature extremes... do some reading or at least drive a car tuned with an M800 and one with a V88.

He could sell the M800 with everything and get a V88 with all motorsport options, installed and tuned for the price he sold it for.

ummm were is dirtgarage when you need him for some good old motec bashing ??? bigmikespec has you idol gone away ? someone has too keep up the fight and it may as well be you now ?

what ecu does swiper the fox's car have now ??? not the inferior one does it ?

even mark is his gtr still run's an motec adl3 and motec e888 to measure the greater temperature extremes you talk about

how many real top level motorsport cars run motec I mean REAL race cars i.e dakar,rally raid,alms then to the national stuff like aus safari,finke,arc,super taxi's

class 1 offshore power boats and the list goes on and on

don't these class's operate in the most rugged extremes of the environment has to offer BUT the vipec is still better

but vipec make you car idle so much better like when does that really matter racing is Wide Open Throttle where it's meant to matter

ummm were is dirtgarage when you need him for some good old motec bashing ??? bigmikespec has you idol gone away ? someone has too keep up the fight and it may as well be you now ?

what ecu does swiper the fox's car have now ??? not the inferior one does it ?

even mark is his gtr still run's an motec adl3 and motec e888 to measure the greater temperature extremes you talk about

how many real top level motorsport cars run motec I mean REAL race cars i.e dakar,rally raid,alms then to the national stuff like aus safari,finke,arc,super taxi's

class 1 offshore power boats and the list goes on and on

don't these class's operate in the most rugged extremes of the environment has to offer BUT the vipec is still better

but vipec make you car idle so much better like when does that really matter racing is Wide Open Throttle where it's meant to matter

Lol... did I say it was inferior? I am not bashing it either, read what I said.

I spoke to Paul "re" Motec and the reason he changed back was for the logging, that being said, the logging is great better than the Vipec at this stage.

I was in a position to buy either, I went in cars with both, my tuner sold both... I chose Vipec

Don't be so naive :blink: motorsport has more to do with sponsorship and marketing than what products perform better.

PS: my comment was regard to operating temperature of the unit itself not measuring

PSS: I would run an ADL3 with my Vipec it is an awesome unit, it is compatable with the V88

ummm were is dirtgarage when you need him for some good old motec bashing ??? bigmikespec has you idol gone away ? someone has too keep up the fight and it may as well be you now ?

what ecu does swiper the fox's car have now ??? not the inferior one does it ?

even mark is his gtr still run's an motec adl3 and motec e888 to measure the greater temperature extremes you talk about

how many real top level motorsport cars run motec I mean REAL race cars i.e dakar,rally raid,alms then to the national stuff like aus safari,finke,arc,super taxi's

class 1 offshore power boats and the list goes on and on

don't these class's operate in the most rugged extremes of the environment has to offer BUT the vipec is still better

but vipec make you car idle so much better like when does that really matter racing is Wide Open Throttle where it's meant to matter

Am I the only one that had trouble reading this?

Try to use some decent grammar mate, your post sounds like it was typed by someone with ADD.

Lol... did I say it was inferior? I am not bashing it either, read what I said.

I spoke to Paul "re" Motec and the reason he changed back was for the logging, that being said, the logging is great better than the Vipec at this stage.

I was in a position to buy either, I went in cars with both, my tuner sold both... I chose Vipec

Don't be so naive :rofl: motorsport has more to do with sponsorship and marketing than what products perform better.

PS: my comment was regard to operating temperature of the unit itself not measuring

PSS: I would run an ADL3 with my Vipec it is an awesome unit, it is compatable with the V88

wasn't there real reason Paul went to motec ???? it can't just be about logging

I'm happy you chose vipec congratulations !!

I'm not naive i just cant stand the crap that some people carry on about

Motec don't sponsor anybody EVERYONE has to pay for it vipec on the other hand i dont know

P.S whats your story about operating temperature of the unit ???

PSS how is the vipec more accurate ?????

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Initially I thought having a pair of Recaro seats would be a big bonus, it turns out these do get a little uncomfortable on long journeys (my fault, not the seat). I had a look through the GSM Performance website at reclining seats and booked an appointment to visit their show room. I got the Recaro Sportster CS for the R34 from here, was very happy with the service received so of course a re-visit was in order. Unfortunately the two Corbeau seats I had chosen aren't on display but they had 4 other options available. Two seats dug into my back, one dug into my legs and the other was perfect. I also found out that Recaro seats use a larger bolt pattern so some adaption was required. Luckily GSM offer some universal adaptors that should solve this problem. I searched the interwebs for price comparisons and Corbeau themselves were the cheapest at £300 cheaper (for the pair). I asked GSM if they could price match, unfortunately they couldn't. I later received an email saying Corbeau would honour them the same discount, but the purchase was already made. I did however order the brackets from GSM, both arrived on the same day. I started with the passenger side seat, knowing this was going to be a little trial and error. There are 3 mounting holes at the front and 2 at the rear on these JURAN Racing seat rails.  With the adaptor brackets mounted, the allen cap bolts started to push into the seat, NOT GOOD!  The rear mounting holes lined up but there were issues at the front. The holes were 1/2 hole out, so the brackets got a tickle with the drill to modify the holes. The supplied bolts weren't going to be long enough and a spacer was needed to stop the adaptor bars from bending. A local fasteners company supplied be with some nylon spacers and longer bolts (M8x30, although these will be replaced with 35mm long shortly) A before and after I pre-drilled the front bracket before making a start on the driver's seat to save some time. And in no time at all that was in the car too. The all black seats have transformed the interior and these are MUCH more comfortable. The only downside with the new Corbeau seats is I sit a little higher, but I'll happily accept that over discomfort. The Youtube video can be found here: https://www.youtube.com/watch?v=wPyttKPktXA
    • All 3 I guess. The car came with the JASI Aero 4 door Type R Full Kit unpainted so this was one thing at the top of my list to complete then I noticed there were body panels parts for this kit so i picked them up along with some black mesh to fill in the front bumper and front side air vents. car is at a paint and body shop atm completing this work. Next I will be addressing the internal bells and whistles, great summer project I can do with the kids.  full interior removal - ,boys car sound deadening - pads and spray ,boys stereo, sound, lighting - Big 3, GTT or bigger alternator ,kids head lining - dye black add star lighting mod ,daughter. That's it for the next 5-6 months. I have some motor maintenance  work i have to plan out. oil filter relocation, gaskets, mounts. beyond that, mind is starting to turn over if i can use a DET intake plenum, block off turbo ports & pipe in a air intake.      
    • roller coaster of a ride. Alarm system was removed & main harness was repaired where possible. still no fix just random successful starts. moved on to the replacing the ignition switch and relay. well all this troubleshooting & repair has been going on, the car is at a paint and body shop being pushed around. Ive been going down there on odd days after work to get it sorted.     
    • 5th November if you want to come out for a spin wakfield
    • PROBLEM WAS BROKEN COOLANT SENSOR!!! Replaced with a new one and its running mint.
×
×
  • Create New...