Jump to content
SAU Community

Putting The Headlight Caps Back On With Hids?

TUF250

By TUF250,
in Exterior & Interior Styling

 Share

Recommended Posts

TUF250 Proficient

TUF250

Posted
Posted

Hi all. I just bought some HIDs for my r33 skyline. They are great, really pleased.

but... the new wiring for the new globes means that I cannot get the caps back on the headlights as the new wiring will be squashed. really didnt want to hack up the wire so I can return it to stock if i have to. needs the caps because i dont want dust or water in there.

any good ideas from people who have done this before? pics would be awesome

thanks

Mr Eps Grand Master

Mr Eps

Posted
Posted

...sorry to get all "dad" on you here...

but R33 have reflector headlights.. HIDs are generally used on projector headlights because of the single direction that projectors give..

generally speaking- R33 have reflectors.. and - VERY badly corroded headlight lenses.. a lot of people will opt for HID because their lights are "weak"

a lot of the "weakness" is because people don't take care of their headlights, when you put HIDs on them - it just makes the problem worse because you have even MORE light which shines off in every other direction.. which is gay..

all i'm saying is - if you went a ghetto plug n play HID kit - i hope you cleaned and reonditioned your headlights FIRST... if not - RECONDITION them!!!!

Mr Eps Grand Master

Mr Eps

Posted
Posted

to summarize on reflector lights the light showers here there and every where. it gets a lot worse when the lens isn't crystal clear... light literally dissipates into a million thousand different directions.. one kit I recommend is glassylite.. 40 a kit and it gets best results ever.. available from auto1.. my results are in attached picture.. sorry to off topic you but i'm just saying hid isn't the only answer.. you should recon lenses even as support..

post-13494-1286173981_thumb.jpg

post-13494-1286174090_thumb.jpg

Charles89 Grand Master

Charles89

Posted
Posted
Hi all. I just bought some HIDs for my r33 skyline. They are great, really pleased.

but... the new wiring for the new globes means that I cannot get the caps back on the headlights as the new wiring will be squashed. really didnt want to hack up the wire so I can return it to stock if i have to. needs the caps because i dont want dust or water in there.

any good ideas from people who have done this before? pics would be awesome

thanks

To reply to your question, what you were meant to do was actually cut a big hole on cap, so you can fit all your wires and stuff through.

Not sure about your HID kit, but mine came with a litte rubber plug, that plugs into that big hole that you'd cut, so nothing can get into the headlight.

If your HID kit didn't come with the rubber plug, then I guess use some sort of tape or something.

RusH_ Veteran

RusH_

Posted
Posted
To reply to your question, what you were meant to do was actually cut a big hole on cap, so you can fit all your wires and stuff through.

Not sure about your HID kit, but mine came with a litte rubber plug, that plugs into that big hole that you'd cut, so nothing can get into the headlight.

If your HID kit didn't come with the rubber plug, then I guess use some sort of tape or something.

+1 to this

TUF250 Proficient

TUF250

Posted
  • Author
Posted

AHA! thats what that rubber plug is for! It wasnt explained in the instructions, that makes perfect sence now. I will do that next week. Thanks for that!

In reference to my headlights I have used the restore kit and my lenses are in great, near new looking condition. The reflaectors appear in very good condition and mine is a genuine low k one aust owner car which prob helps. I only bought HIDs because i like the look and do a bit of night driving so the extra light helps

thanks guys!

.:: GimpS-R34 ::. Grand Master

.:: GimpS-R34 ::.

Posted
Posted

drive up the road.. and get a mate to drive towards you and see if the light gets in his eyes... some lights arent designed for HIDs and glare horribly in others eyes.. check if yours do this as its dangerous and f**king annoying..

NYTSKY Grand Master

NYTSKY

Posted
Posted
Hi all. I just bought some HIDs for my r33 skyline. They are great, really pleased.

but... the new wiring for the new globes means that I cannot get the caps back on the headlights as the new wiring will be squashed. really didnt want to hack up the wire so I can return it to stock if i have to. needs the caps because i dont want dust or water in there.

any good ideas from people who have done this before? pics would be awesome

thanks

Just put a slight notch on the side of the cap, then slide the wire into the notch. This will enable you to put the cap back on without squashing the wire.

Charles89 Grand Master

Charles89

Posted
Posted
it wasn't explained in the instructions??

it's probably because your instructions looked a bit like this..

hieroglyphics.jpg

I think that says.... put a bird into your headlight and it will hold your HID bulb in place? No? lol

PIG747 Mentor

PIG747

Posted
Posted
Just put a slight notch on the side of the cap, then slide the wire into the notch. This will enable you to put the cap back on without squashing the wire.

i fitted a set last night and did the exact same thing

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      R33 Fuel Pump & Brakes after alarm swap

      By MBS206 · Posted

      Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • GTSBoy
      After market rear camber arm adjustment

      By GTSBoy · Posted

      Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...