Jump to content
SAU Community

Recommended Posts

  • Replies 172
  • Created
  • Last Reply

Top Posters In This Topic

floor mats sold

grill sold

front blinkers/ fog lights sold

front and rear bar sold pending payment

ac compressor sold pending payment

Edited by Goodo

how much can you do the drivers side door shipped to 4226 qld?

if your anywhere near syd or canberra on the 8th or 9th of nov i'll take it off your hands

does it have the stock 17's on it?

if so, how much are you after?

how about some m35 17's ( 235 x 45 x 8.5)

with slight curb rash!

with some japanese autogaurd tyres ... $100 plus postage

what steering wheel you got mate? if its momo, i'll almost definately take it, even if its just the normal type as long as its in good condition i might take it... just want an airbag wheel as my new stag has a MOMO jet wheel on it :)

what steering wheel you got mate? if its momo, i'll almost definately take it, even if its just the normal type as long as its in good condition i might take it... just want an airbag wheel as my new stag has a MOMO jet wheel on it :)

I dont have the momo wheel but i do have the standard one in what i would call pretty good nick give me your email address and ill send you a pic

  • 2 weeks later...
Hey. Do you still have the metal clips that hold the rear metal pate on the back of the hood lining. Mine are all broken. Thanks

yeah i will say i would but im not 100% sure which parts you mean if you could take a pic of yours just so i can see what i am looking at thanks nathan

il grab apic when i get a chance but if you open the boot and look at the hood lining there is a metal plate that goes from one side to the other on the back edge just inside the hatch, i need the clips that hold it on and possibly the plate pending if i can straighten mine.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
×
×
  • Create New...