Jump to content
SAU Community

Recommended Posts

need help from those who have or know bout polishing up an engine bay

ive had my licence suspended for 1month and since the car isnt goin no where

ive decided to polish all the alloys in the engine.

more to the point im using a orbital sander with 320grit paper on the pipe with the stock bov and having trouble getting it smooth all the way down, and am scared to use a thicker paper.

after this process i plan to use a 800grit then a 1200

im also plannng on doin plenum n engine

any suggestions on mayb goin about it a better way or added info on the matter??

also ive already done a search on the topic and it helped only to a certain extent

if anyone has pics it would also b great.

john c

Link to comment
https://www.sau.com.au/forums/topic/34038-polishing-engine-bay/
Share on other sites

It won't become smooth until you start using the other finer grade papers.. then it will start getting a lot shinier. Its hard work and takes many hours but eventually it'll come up.

Just keep going, sounds like you've got the right idea.

end result will do!

post em up

i done all this about 5 months ago. just used sand paper to get all the cast marks out of the alloy then used a polishing cloth on a bench grinder i used 2 stages on the polishing mop for the bench grinder , first a medium compound then fine/mirror. hope this helps.

i couldnt attach my pics cause they are already in a thread here. do a search or look for a thread tittled '' my new look engine bay '' all my pics are there.

here is mine: http://www.skylinesaustralia.com/forums/sh...ead.php?t=31877

.. over time the shinyness does tend to fade a little.

you can also use one of those buffer attachments for a drill and a decent polishing compound if you don't have a bench grinder.

Predator> ok so to sum it all up...you did

1. Sanded down any burs and crap (what grade papers you use?)

2. Polished (use anything specific?)

3. Repeated 1 and 2 until desired shinyness

4. painted (any prep work needed primers etc etc?)

this sum it all up? am taking notes

.. over time the shinyness does tend to fade a little.  

Autosol fixes that... ;)

I have a polished plenum, rocker cover and power steering canister.

It's a fair bit of work to keep it shiny, but it looks pretty :cheers:

Before and after pics of the engine bay can bee seen in the link under my avatar.

it takes a long time but the longer you spend the better it gets. you got the idea of steping down the grade papper, i use wet an dry. apply small amount of water or petrol to sanding surface or papper now and then. you should be able to get a polish finish just with sand papper, then when you buff with polish until black clean off with a new buff (clean cloth or buffer with no polish on it) and it will come up like mirra

Just grab a drill and a tapered grinding stone to start on the deeper areas and all the burrs, gently does it now, then use a flapper wheel attachment (coarse) on the drill then use a fine one with the scotchbrite in between. Then your choice is the buffing attachments for the drill or the bench grinder if lucky enough to own one. If buying a benchy then buy big and powerful NOW not later. Eventually you will have....

http://www.skylinesaustralia.com/photopost...&cat=500&page=1

messiah: yeah autosol works fairly well at polishing, in conjunction with a fast polishing buffer can work wonders. With painting, mine was never painted but once its all smooth I assume after that its fairly easy to paint using any painting method (using the appropriate heat resistant paints)

sky-chicks car is a great example... probably heaps more shiney than mine.

If it doesn't come up great, you may be better off just taking the parts of completely and taking them to a specific metal polisher (see: yellowpages).. they will probably give you a much better result than doing it manually, and saves time. Will cost you a bit of money, but generally its not much as using the proper machinery it can be done in minutes. Then you just have to worry about bolting it all back together.

Once you've finished with the polishing, you can apply a clear coat, but over time the clear coat will start to turn yellowish and dull......

it's easier to leave it raw and autosol it before showing it off. :)

Or get Lanosil from Supercheap. Comes in a pressure can and keeps the shiny stuff looking good. Needs a clean now and again tho. I did the engine bay in the soarer and it looks showroom after a few days driving. Sprayed everything. Got a couple more cans now to do the other cars.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
    • That still isn't a lot to go on. I don't have a Y50 Fuga Head Unit wiring diagram. I can say that a lot of nissans of that age shared head unit plugs, so if you are in Australia something like this would probably help: https://aerpro.com/app091# You plug that into the car loom, then either plug the head unit ISO into that (if it has ISO), or you buy and ISO adapter harness that you wire in. Bit of stuffing around, but once you have ISO its easy to change things in future.
    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
×
×
  • Create New...