Jump to content
SAU Community

Recommended Posts

went out for an afternoon track session today at QR

have had the ME20 Pads in for 1 full and 3 half track days.

have been brutal on them the last 2 times out on the national circuit.

was about to head back out for the second afternoon session when a pair of black lines and some large 50c pieces of the pad material fell from the trailing edge of the backing plates of both front pads

The last inspection of the pads prior to the last half track day showed no cracking of the pad material and reasonable pad thickness.

gallery_56949_3979_457111.jpg

Link to comment
https://www.sau.com.au/forums/topic/340512-brake-pads-disintegrating/
Share on other sites

Endless W003 is the compound we use at Mallala - which is harder on brakes than QR - and no problems :D

went out for an afternoon track session today at QR

have had the ME20 Pads in for 1 full and 3 half track days.

have been brutal on them the last 2 times out on the national circuit.

was about to head back out for the second afternoon session when a pair of black lines and some large 50c pieces of the pad material fell from the trailing edge of the backing plates of both front pads

The last inspection of the pads prior to the last half track day showed no cracking of the pad material and reasonable pad thickness.

gallery_56949_3979_457111.jpg

Mark,

you've had a lot of rain up there recently, do you recall and instances where pads have bound to rotor (say overnight or if the car sits idle for a long period after rain?) you would hear/feel a noticable crack when you first move the car, or the car wouldnt move until you give it some throttle. I have a theory this happens a lot, and weakens the pad material, which then cakes off. Anyway, just a thought. I've never used ME20's, just the ccRG's (they have been fine).

Paul stokell diver training

I got a whole 15 min of drive time. :laugh:

Saw your car on the trialer heading out there! Looking very good :) It was the highlight of an otherwise pointless morning spent walking around in the bushes beside the cunniham highway lol

Saw your car on the trialer heading out there! Looking very good :D It was the highlight of an otherwise pointless morning spent walking around in the bushes beside the cunniham highway lol

So its you flashing passing motorists. :whistling:

How so Mark, Was there A lot of lecture time etc, or just too many peeps ?

Nah Noel I missed the first session as i was late from work and then the pads went after my first session out.

Didn't take a spare set of pads so called it a day.

Saw your car on the trialer heading out there! Looking very good It was the highlight of an otherwise pointless morning spent walking around in the bushes beside the cunniham highway lol

hope you weren't throwing rocks at it from one of the overpases!

Thanks,

Are u going to pirelli day on the 20th?

I might do those next year Drew. next track outings

- Lakeside 31st Oct (first time out there, really looking forward to it)

- QR 23rd Nov Round 6 Ruzic time attack series

Edited by handbrake

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Jack the back of the car up, pull that wheel off, pull that sensor out, and put a bore scope into the hole to inspect the outer casing, see if anything looks damaged before you pull the whole thing apart.
    • Ergh... So I pulled the speed sensor out again and the tip was shiny so I think it's rubbing the bearing. The bearing contains the magnets for the speed sensor so I think when the first sensor broke it damaged the magnet ring on the bearing.  This is just a Google image, but there is a hole going to the bearing. So when the tip broke off the old sensor I'm guessing it fouled the bearing... As the magnet is only protected by a plastic cover it would be easy to damage it. So I guess I'm doing a bearing again.   
    • My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
×
×
  • Create New...