Jump to content
SAU Community

Recommended Posts

pretty sure wrx injectors are side feed? maybe they use either or depending on engine model

injectors arent necessarily engine/car specific so dont get worked up just yet :thumbsup:

to my knowlegde some of the STI come out side feed and a few come out top feed

Lol, no worries :(

Well thanks again to Oz for helping me out; it seems I may have hit a snag. Will go and discuss it with my tuner tomorrow, but unfortunately these injectors are a far bit bigger than the standard GTT injectors so it doesn't look like they will fit. Everything else is the same, plugs will fit, injectors will fit into the rail... But the rail is going to require a rather large spacer to fit them. Does anyone know how large a spacer you can use on the R34 rail before it fouls on the plenum? These injectors look like they are going to require around 1cm to fit...

that is how they are supposed to fit. with spacers in the rail. and yes most likely the seller took these out of his car and replaced them with new sard injectors and put the old injectors into the sard boxes for posting to you. that is the most likely explanation. not sure what made you so paranoid. not everyone is out to rip people off. :no:

if these things worry you and you have trouble trusting people it's probably wise to just buy stuff brand new. it will cost more but it will come in boxes clearly marking what the stuff is.

Yeh I know most injectors require a spacer, I was expecting to have to use a spacer, but 1cm is huge. If they fit, it's going to be very very close to hitting the plenum. Should be able to work something out though.

The seller said he was selling his car so he wasn't going to bother upgrading the injectors. He never installed these injectors in his car, he bought them and had them sitting around for a year before he decided to sell his car along with all the mods he had planned for it. Which is why the Sard boxes made me curious. As well as the fact I got them so cheap when they are basically brand new. I just wanted to know for sure what type of injector they were, not that I was putting some crappy Chinese rubbish in. The boxes are very faded and worn as well.

I'm not normally paranoid, but with my fuel system I am. Not all people are out to rip people off, but some are, so I thought it better to be safe than sorry. I had no intention of buying second hand until these came along, the guy seemed genuine and I got them really cheap so I couldn't go past them.

fair enough. well given how cheaply you scored them, and given that they are second hand and possibly not what you think they are I'd say it's worth spending $100-$150 getting them cleaned and flow tested. any good workshop or EFI specialist place can do it for you and then you'll know EXACTLY what they flow. :D I agree fuel system is deadly important. definitely not an area I ever skimp on.

  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...