Jump to content
SAU Community

Recommended Posts

go front strut bar and sway bars.... front and back.... even with stand springs and shocks, you will still easily out manevour most cars....

you trying to get me broke?! :)

you keep giving me ideas to add more mods to the car, probably end up doing a RB25DET engine transplant and a T88 and nos.... :headspin:

  • Replies 62.7k
  • Created
  • Last Reply

Top Posters In This Topic

  • chaos

    7164

  • Ska

    5791

  • BelGarion

    3645

  • Nexus9

    3590

Top Posters In This Topic

yeh but dont forget exhaust...will be lower than your standard one

not really benny boy... max piping size for NA should only be 2.25 inch catback and muffler size is almost same as stock....

you go anything more than 2.25, you will lose back pressure.... less torqy....

you keep giving me ideas to add more mods to the car, probably end up doing a RB25DET engine transplant and a T88 and nos.... :headspin:

ME giving you ideas?? :confused:

i would go handling first..... no point spending thousands to squeeze a few more KWs outa the car...

awesome handling makes you a better driver...

not really benny boy... max piping size for NA should only be 2.25 inch catback and muffler size is almost same as stock....  

you go anything more than 2.25, you will lose back pressure.... less torqy....

I've got a twin cannister 3.5" exhaust sitting in the garage :)

ya, I'm going for tyres first Glenn costing me a butt load too.... almost half my uni tuition.

can sometimes even be just be the gaskets or rubber mountings.. gaskets are like $2.50 to replace

where can i get this checked out? at a normal garage???

yup.. not cheap..

krawler: no.. they're just spring and shock setup.. i sold my old set for $200, they were sitting around for ages

Doesnt coil over simply mean the coil is over the shock?

Meaning that most cars are coil over factory.. The term coil over is normally targetting adjustable gear though.

i know... It was on the NA, but got it taken off for compliancing.. and power loss.

now i'm stuck with a stupid rattle.

get 2 jacks and a creepboard.... rip out the heat shield....

if not the heat shield... hammer the resonator gently to check for rattling...

i think the difference is.. with coilovers, the shock is actually welded to the bottom of the spring, and they are basically one unit and cannot be separated. Most things can be adjustable.

With a spring and shock setup the springs and shocks can be separated and changed independently. In that setup you can adjust the shock, but not the actually spring height or anything like that.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • What copper washer do you guys use on the bleeder bolts? The existing one I have I had no idea where to find it in a local store, I did buy some online but that are only 1mm thick whereas my old one is 2mm+ thick and when I put the new washer out and squeeze the top radiator hose I can hear a bit of air but not with the old one. Does this matter? The new one doesn't leak, but the inner diameter is a bit loose whereas the old one threads on the bolt.
    • Howdy all, after being out a few weeks ago on a spirited drive in my GTR I have 2 issues that oddly have appeared at the same time. Whilst accelerating quickly through the gears all of a sudden i’ve lost power at the top of third gear (below redline around 6000rpm) for no obvious reason.    From that point onwards the car has been running rich on idle, won’t really rev under load without a ton of black smoke and the odd backfire, and dying as a pull up to a set of lights unless I keep the revs up around 1500rpm. In addition when shutting down the car that same night (I was 10 minutes from home) I noticed one of the turbos was significantly noisy on wind down when shutting off the engine. After letting the car cool down overnight it starts up fine, although once it gets to temp the revs start to creep up and down, the exhaust is darker than it should be and it also sounds like it’s running rich (fat note) I’ve put a new set of plugs in it - no change, the old plugs all seemed OK with two of them being somewhat richer/fueled up than the other 3 with 1 being borderline. I’ve smoked tested the intake system via the front of the Turbos, found a split vacuum hose going to the factory boost gauge sender, which I have since replaced.  Also found another leak on the gasket coming off the rear turbo outlet, have also replaced this. After fixing both of these leaks - still have the running rich issue. I’ve also tried another pair of AFM’s - no change here After pulling off the front turbo intake pipes, there is obvious shaft play in the front turbo, which now hisses loudly on light revvs although I can’t see why this would make the car run funny even under idle. I’m curious to know why it’s running rich before I potentially replace/rebuild turbos. The car is completely stock <50,000kms  other than an exhaust. Oil and coolant are all clear. I haven’t bothered with coil packs as it looks like they won’t be the issue due to condition of the plugs. Any help appreciated as I cry myself to sleep!
    • No probs at all. I used to love trying to dig up obscure info for those in need where possible going back 20+ years on SAU.  I did have another look and couldn't come up with any closer match. I'm leaning towards those skirts in your first pic are custom fitments, cut down/extended or from another car entirely and modded to fit an R34 sedan. I would've thought someone in Japan had them and taken a photo at some stage over the last 2 decades but there's nothing. Someone out there must know surely.
    • Welcome mate. Any pics? Even with a DE I'd be well happy if I had that as a 1st car. 
×
×
  • Create New...