Jump to content
SAU Community

Recommended Posts

Do RB26 (R32/R33 GTR) injectors fit into RB20 without any mods?

Not concered about resistence, as I am looking to do a ECU swap (most prob Microtech LT-12S or Wolf3d) which will allow me to run low-impedence injectors

Just want to know if the plug straight in without any mods, and if mods are required what where they

from memory they are around 440cc arent they?

Looking to make around 30rwkw more (200 at the moment) and don't want to run a regulator, so I would think that GTR injectors are more than capapble of this

Thanks heaps

Link to comment
https://www.sau.com.au/forums/topic/34332-gtr-injectors-into-rb20-question/
Share on other sites

  • Replies 121
  • Created
  • Last Reply

Top Posters In This Topic

thought about them, but for GTR injectors selling for around $300, they are a bit of a bargain for injectors that flow 440cc

440cc will be plenty for what power I am after, 550cc is a bit of a overkill I reckon. If I was going for a bigger turbo or chasing 300rwkw for sure, but for my bolt on RB20 440's will be fine

Just got to find out if they will fit thats all :cheers:

OUt of intrest, what do the RX injectors sell for?

If you are interested I have some (40,000km) stock R33 GT-R injectors for sale.

I am coming past Adelaide in 2 weeks, PM me

No probs, just gotta find out if they are going to fit first

I have a '92 R32 GTST with RB20DET, and if resistance isnt an issue with the ECU, then they bolt into place as though they were std RB20 injectors...and yeh if you dont need 550cc injectors then the 440cc GTR injectors seem to go for less than half the price.

Even if you are still running a std remapped ECU, the GTR Injectors WITH A resistance pack works fine and only took me about 4-6 hours to install and wire up...would have been quicker if i could have gotten the silly throttle body off!

cool, what about the injector plugs and such, do these need swapping or do the RB20 plugs fit? So its just a matter of pulling the old ones and dropping in the RB26 injectors?

Do you know if R32 GTR injectors differ from R33 ones?

Ok cool, sounds like they will fit without any drama's

Has anyone actually tried this combination of GTR injectors on a RB20, running Microtech/Motec/Autronic/Wolf3d ?

chris yes they will fit in no probs, and the plugs are even the same. Should work well, and not cause any probs with overfuelling at idel, the 550s can cause a little trouble with a stock rb20 and computer but any aftermarket management should handle the 550s fine, but they do however reqire the plugs to be changed, so get the gtr ones if you can find a nice set.

I am using 13B non turbo injectors which are either 420cc or 460cc Lol damn memory! Anyway I got them from a fella from nissansilvia.com for $35 each. They fit straight in, the last 4 digits are 1350 from memory??? Anyway I also, during the conversion got new injector plugs, which are similar to the stock ones except the lug is in the centre and not offset. They also have the spring you push down to unplug them vs the spring clip that gets flicked off and lost. I am running a microtech LTX12 (a 180sx RB20DET) and haven't got the car back yet so I cannot comment on the further.

Where do you get the resistor pack for them and how is it wired up?

I used the resistor pack from a GTR, so try ppl that are wrecking a GTR, or have half cuts etc etc. But in theory i cant think of any reason why you cant just go and buy 6 resistors from Jaycar and solder them in line. (I THINK the resistance of the GTR pack was 6.??ohms)

As for wiring them, if you are a confident DIY person who knows wiring diagrams and electrical circuits then it all to easy to do. If you dont, then it may be a little more awkward...

If you re going to be paying someone to do it then be sure they have done it before or know RB wiring backwards otherwise you will be paying a premium for them to learn on your car which doesnt make it such a cheap option when they want $500 to install. :thumbdwn:

chris yes they will fit in no probs, and the plugs are even the same.  Should work well, and not cause any probs with overfuelling at idel, the 550s can cause a little trouble with a stock rb20 and computer but any aftermarket management should handle the 550s fine, but they do however reqire the plugs to be changed, so get the gtr ones if you can find a nice set.

Sounds good mate, hopefully I will get some soon and get the ball rolling. Might need your help when it comes to fitting, I want to do most of the work myself but I know you have had injectors in and out of your RB20, so a bit of a watchful eye from someone who has done it before might be handy!

Will be re-doing the turbo to airfilter pipe as well, as I am doing away with the AFM, so will also drop by and get you to have a look at that

Hows the RB~? coming along? What type of managment are you going to run?

I used the resistor pack from a GTR, so try ppl that are wrecking a GTR, or have half cuts etc etc. But in theory i cant think of any reason why you cant just go and buy 6 resistors from Jaycar and solder them in line. (I THINK the resistance of the GTR pack was 6.??ohms)

As for wiring them, if you are a confident DIY person who knows wiring diagrams and electrical circuits then it all to easy to do. If you dont, then it may be a little more awkward...  

If you re going to be paying someone to do it then be sure they have done it before or know RB wiring backwards otherwise you will be paying a premium for them to learn on your car which doesnt make it such a cheap option when they want $500 to install.  :thumbdwn:

Im game enough to DIMyself but with the GTR resistor pack where is that located in the loom?

Im game enough to DIMyself but with the GTR resistor pack where is that located in the loom?

Physically the resistor pack is bolted to the right/drivers upright. It rectangular, about 80x30x45mm in size and is a ceramic resistor with a thin steel cover. It will have 6 blue wires going to it and one other wire, i cant remember the colour. Basically the 7th wire is the power wire whilst the 6 blue wires go to the injectors.

From a wiring diagram perspective the resistor pack goes between the power supply to the injectors and the +ve terminal of each injector

Physically the resistor pack is bolted to the right/drivers upright. It rectangular, about 80x30x45mm in size and is a ceramic resistor with a thin steel cover. It will have 6 blue wires going to it and one other wire, i cant remember the colour. Basically the 7th wire is the power wire whilst the 6 blue wires go to the injectors.

From a wiring diagram perspective the resistor pack goes between the power supply to the injectors and the +ve terminal of each injector

So what ill need to do would be to change the Gtst resistor pack to the GTR one? or is dont gtst have a resistor pack as such?

thanks Roy much apreciatted!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...