Jump to content
SAU Community

Recommended Posts

Leftovers from wrecking r33 series 1.5 all parts located in sa adel hills. clearing out for room.

lhs front gaurd $50

rhs front gaurd $50

rhs front headlight $50

gaurd orange indicators $10 pair

dash missing two small vents on top $80

center consol 40

heater/aircon control $40

heater $80

entire floor carpet $50

roof lining $20

center roof light $5

map lights $10

holy shit handles on roof $5

lhs a pillar $10

speedo cluster $80

glovebox $20

rhs sun visor $10

rear lhs tail light $80

passengers door$100 with all electrics

door linings and electrics can be separated along with mirrors

side skirts (one broken in half) $30 pair

windows (remove yourself or get removed properly) $$$

3"catback exhaust with emptied cat and rear cannon $200

interior lining $50

parcel shelf $20

boot lining $40

boot seal $15

bonnet latch $30

horn $10

fuel tank $50

rear skyline strip between lights $40

scuff panels inside doors $20 pair

fuel cap covering panel $10

windscreen wiper stalk $10

indicator stalk $10

steering column $20

rear rotors and calipers $150

front 5stud hubs $100 pair

standard diff $150

front suspension $50

rear subframe $200

r32 rear spoiler mspec 40$

r34 gtr front indicators (orange) $40 pair

r34 side indicators $20 (orange)

0419837474 prefer sms or call as apposed to pm, thanks

  • 2 weeks later...

rear rotors and calipers sold

subframe sold

sideskirts sold.

rest offers on the lot, all taking up space. also brake booster availble too.

whats with getting text messages at about 4 in the morning after car parts......do people really sit on here and browse this early?lol....anyways still few bits to go..just using up room now..

  • 4 weeks later...

do u have passenger door for the 33 still ,if so how good is it paint ,dents,rust etc as i am pretty fussy thanks Darren

do u have passenger door for the 33 still ,if so how good is it paint ,dents,rust etc as i am pretty fussy thanks Darren

yep i just removed it then. i couldnt find any dents or rust on the door. the triangle section where the side mirror is inserted however has rusted, its not visible when the mirror is in, so if you were to treat it and apply an undercoat its not going to affect what you see anyway as its hidden.

the rest of stuff i really want gone so open to offers.

the shell has been sold sowhat i have listed in origional post is all available, prob a few bits gone since.

the entire steering rack i pulled out thismorining- also heater unit. (please no msgs like "will u post steering rack to syd for $100 inc postage" because no i wont. postage alone is probably more than 100$ so please no time wasters like i have previously"

so ...bump to see everything gone

Hey

is the mspec spoiler like a standard gtr one? (forgive my ignorance)

thanks

hey

the gtr spolier is not the same as the mspec. gtr spolier is u shaped and does not have a center connction to the boot. the mspec one i have connects at both ends of the boot and also in the center and is really only about a cm maybe a touch higher gap between spolier and boot. it also has a brake light inbuilt into it. which if you dont like can fibreglass up. if you want a photo sms me and il mms a photo through.5114250195_c60415c9ec_z.jpgthis is like the spoiler i have, in undercoat,

90blackgtst32.JPG gtr spolier

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...