Jump to content
SAU Community

Recommended Posts

Recently replaced the rack in the S13 with an S15 unit which required using the s13 rack ends. While I tried to take good measurements before and after, naturally my toe is a bit out.

I've had a read and learned how to take a toe reading using the string line setup and am now adjusting.

I'm curious what others are running on circuit setups. I'm just going to have a look back to my last alignment paperwork and try to match that as the car felt good to me but I'm still curious what others are doing.

My home track is Winton so not massive top speeds where the straight line stablity of toe in might be paramount.

I can't recall exactly until I see the paperwork but I think it had about 1mm of toe in previously, with -2.5 camber, can't remember the castor reading.

I'd say I've ended up with about 2-3mm total toe out up front.

Do you guys drop the tie rod end and spin it on the rack end or leave the tie rod end attached and spin the rack end inside the tie rod end thread.

I was dropping the tie rod, the flat surfaces on the rack end to get a spanner on it looked a little rough and small.

Downside being I could only adjust in larger increments with the tie rod end method, think I'll see how it drives then use the rack end adjustment for fine tuning.

Edited by ActionDan

went for a drive, feels pretty good and drives straight so that's a good start.

Reason the rack went in was to sort a dead feeling it had after the last deca. Feels better than it did but still has moments where it feels suspect though, so maybe it's the pump :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • BOVs do have a purpose, if you ever log pressure before and after the throttle body, you will see a spike pre throttle on lift off from a WOT condition. Enough to bend throttle blades / damage e-throttle motors or simple assist in blowing off cooler pipes. FWIW, the above on really applies to those running at least 2 bar of boost. OP shouldn't have an issue, on the other hand, here are some videos of my shit box over a decade ago with some succulent dose with the airbox on and off. That shit box is unrecognisable these days 🫠    
    • I've tried all different combinations of BOVs/ no BOV and stock bypass valves over the years, on gear changes the stock bypass valve seems to get the car back on boost quicker because in part the turbos wheel speed isn't being slowed down by reversion, although they have issues holding boost much over the stock setting. Most aftermarket BOVs you can adjust the spring, tighter will make it open later and close sooner, but in my experience it'll cause a bit of flutter at low load/rpm anyway. I've also got some input into this whole no bov causing turbo wear, never had an issue on any on my turbos HOWEVER, I got my R33 GTST with 200k kms on it, with from what I can see still has the original turbo, no lateral shaft play but has about 4-5mm of play in and out which to me seems like a worn thrust bearing from years (100-150k kms?) of turbo flutter running no bov, so maybe there is some truth to it in the long run. But that'll never stop me loving the Stutututu while I have the car.   OP just wants to know if he can run a atmo vented BOV with no major issues and the answer is YES, plenty of people do it, there's no harm in installing it and seeing how it runs before spending $$$ on an aftermarket ecu, last time I bought a Nistune it was $2400 for install and a tune , unsure of todays prices but you get me. Crazy money to spend just to fix the minor inconvenience of stalling that can be overcome by letting the revs come down to near idle before putting the clutch in or a little bit of throttle to avoid it. You're better off leaving the ecu and tune for after a bigger turbo/injectors have been installed to take full advantage of the tune and get your moneys worth.   Let OP have his Whoosh sound without trying to break his bank haha
    • I see you missed the rest of the conversation where they have benefits, but nothing to do with avoiding breaking turbos, which is what the aftermarket BOV made all the fan boys, tuners, and modders believe was the only purpose for them...
    • But they do so for the other reasons to have a compressor bypass. It's in the name.
×
×
  • Create New...