Jump to content
SAU Community

Recommended Posts

The trionic system uses the resistor ® type spark plug to read combustion chamber conditions and "inform" the ECU about boost and ignition advance requirements for the engine in real time and continuously. This is why you must use resistor type plugs

wtf? :)

Hanaldo, here it is in a nutshell.

Iridiums and platinums have the benefit over coppers that the centre electrode lasts longer and therefore the plugs have a longer life. This you have understood correctly.

This is why nearly all cars from factory come with iridiums/platinums and why most people in a standard car run iridiums/platinums.

In a modified car pushing a lot of boost and horsepower the centre electrode and ground electrode fouls up quicker than they do in a stanadard car. Dependent on the tune they can foul up a hell of a lot quicker.

Since they foul up they will start to missfire. This has nothing to do with what the electrode is made out of, it will happen regardless.

Since plugs foul up quicker in a highly modified car, there is not much point using an expensive iridium/platinum spark plug. Hence people use the cheaper alternative, a copper.

Now the added benefit of a copper plug is they can be gapped down when high boost levels are used. You are not ment to gap down an iridum/platinum plug because the electrode can get damaged very easily and render the plug useless.

So yes your tuner is right, however I don't think you will need to go below a 0.8 gap. I have run 20psi and nitrous through mine on a 0.8 copper plug through Splitfire coilpacks and not had a missfire if the plugs were in good condition.

As for the resistor plug, yes he is correct, you are ment to use a resistor spark plug on a RB ignition system. Personally I don't know what the effects are of not running one on an RB are as I have never done so.

So to conclude you want the following spark plug in an RB engine:

BCPR6E

Obviously the heat change is dependent on mods. I use 7's because I need to for the nitrous and high boost level. Other plugs will fit such as:

BPR6E

BPR6ES

BKR6E

etc.

The main differences here are the S on the end stands for "Standard", which means the spark plug doesn't have a V groove on the centre electrode which is ment to give a better burn. So if you can, get one without the S on the end.

And the main difference between the BKR and the BCPR is that the BCPR is slightly longer on the end of the spark plug going into the coil pack than the BKR.

Inside the coilpack there is a little spring that makes the connection between the coilpack and the spark plug. The BCPR compresses this spring more and gives a better contact (once again helps against missfires.)

*I used to sell NGK plugs for years at Autobarn and had many talks with the NGK rep. On a weekly basis I would get guys in imports coming in complaining about missfires due to them running wrong plugs*

Edited by PM-R33

i've run both resistor and non resistor type with no noticeable difference, works the same either way but yes technically your supposed to use resistor type for skylines.

coilpacks are the biggest factor when it comes to plug gaps, for example when i had standard coilpacks, which were pretty tired, i had to gap the plugs down to ~.5mm to stop it misfiring under boost. yes this isnt ideal but its better than misfiring and fixes the problem until you can get new coilpacks. every cars different but basically you want to run the biggest gap you can without misfire. if you can play around with gaps yourself do some experimentation to find what works best, if your paying a mechanic then its probably best to just go straight to .7-.8

Hanaldo, here it is in a nutshell.

Iridiums and platinums have the benefit over coppers that the centre electrode lasts longer and therefore the plugs have a longer life. This you have understood correctly.

This is why nearly all cars from factory come with iridiums/platinums and why most people in a standard car run iridiums/platinums.

In a modified car pushing a lot of boost and horsepower the centre electrode and ground electrode fouls up quicker than they do in a stanadard car. Dependent on the tune they can foul up a hell of a lot quicker.

Since they foul up they will start to missfire. This has nothing to do with what the electrode is made out of, it will happen regardless.

Since plugs foul up quicker in a highly modified car, there is not much point using an expensive iridium/platinum spark plug. Hence people use the cheaper alternative, a copper.

Now the added benefit of a copper plug is they can be gapped down when high boost levels are used. You are not ment to gap down an iridum/platinum plug because the electrode can get damaged very easily and render the plug useless.

So yes your tuner is right, however I don't think you will need to go below a 0.8 gap. I have run 20psi and nitrous through mine on a 0.8 copper plug through Splitfire coilpacks and not had a missfire if the plugs were in good condition.

As for the resistor plug, yes he is correct, you are ment to use a resistor spark plug on a RB ignition system. Personally I don't know what the effects are of not running one on an RB are as I have never done so.

So to conclude you want the following spark plug in an RB engine:

BCPR6E

Obviously the heat change is dependent on mods. I use 7's because I need to for the nitrous and high boost level. Other plugs will fit such as:

BPR6E

BPR6ES

BKR6E

etc.

The main differences here are the S on the end stands for "Standard", which means the spark plug doesn't have a V groove on the centre electrode which is ment to give a better burn. So if you can, get one without the S on the end.

And the main difference between the BKR and the BCPR is that the BCPR is slightly longer on the end of the spark plug going into the coil pack than the BKR.

Inside the coilpack there is a little spring that makes the connection between the coilpack and the spark plug. The BCPR compresses this spring more and gives a better contact (once again helps against missfires.)

*I used to sell NGK plugs for years at Autobarn and had many talks with the NGK rep. On a weekly basis I would get guys in imports coming in complaining about missfires due to them running wrong plugs*

i agree :(

So to conclude you want the following spark plug in an RB engine:

BCPR6E

Thanks for all the info, Phill.

Would the following be alright to purchase??

http://cgi.ebay.com/ebaymotors/4-NGK-V-Power-Performance-Spark-Plugs-BCPR6E-11-5632-_W0QQcmdZViewItemQQhashZitem45f4ff0ad7QQitemZ300463098583QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories

apart from the 1.1mm gap they'll be fine. you'll probs have to gap them down a bit

Thanks, ended up buying some other random sparks from a shop down the road. I'll get the deet of them when i get home (if I remember) and I'll post them up.

They seem to be running alright.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...